图书馆订阅: Guest
Begell Digital Portal Begell 数字图书馆 电子图书 期刊 参考文献及会议录 研究收集
国际能源材料和化学驱动期刊
ESCI SJR: 0.149 SNIP: 0.16 CiteScore™: 0.29

ISSN 打印: 2150-766X
ISSN 在线: 2150-7678

国际能源材料和化学驱动期刊

DOI: 10.1615/IntJEnergeticMaterialsChemProp.v5.i1-6.550
pages 513-522

BURNING RATE AND PRESSURE DEFLAGRATION LIMIT (PDL) CHARACTERISTICS OF A GAP/AP PROPELLANT SYSTEM

Keiichi Hori
Institute of Space and Astronautical Science (ISAS), Japan Aerospace Exploration Agency (JAXA), 3-1-1 Yoshinodai, Chuo-Ku, Sagamihara, Kanagawa 252-5210, Japan
Masahiro Kohno
Institute of Space and Astronautical Science, 3-1-1 Yoshinodai Sagamihara, Kanagawa 229, Japan
Angelo Volpi
CNPM- National Research Council, Viale F. Baracca, 69 20068 Peschiera Borromeo, Milano, Italy
Claudio Zanotti
TEMPE - National Research Council Via Cozzi 53, 20125 Milano, Italy
Kazushige Kato
Research & Development Department, Taketoyo-Plant, NOF Corporation, 61-1 Kitakomatsudani Taketoyo-cho, Chita-gun, Aichi-ken 470-2398 Japan
Shigefumi Miyazaki
Research & Development Center, IHI Aerospace Co., Ltd. 21-1 Matobashinmachi, Kawagoe-city, Saitama, 350-1107, Japan

ABSTRACT

For the application to a mass flux controllable gas generator, GAP is one of the most suitable high energetic materials because of its relatively high pressure exponent. However, its PDL and low pressure burning rate characteristics are not fully investigated yet and it is necessary to know them in detail for such an application. Moreover, a GAP/AP propellant system is considered more feasible because the addition of AP to GAP may be effective to extend the combustible region. Therefore, peculiar attention should be paid to burning rate characteristics of a GAP/AP propellant system.
High pressure burning rate of a GAP/AP propellant system has been obtained with a strand burner, and PDL and low pressure burning rates have been investigated by means of a X-ray device as functions of AP content, AP particle size and depressurization rate. The X-ray device is, basically, composed of X-ray source, combustion chamber and X-ray sensor, and the depressurization rate is controllable. The signal at the output of the sensor is sent to a digital acquisition system controlled by PC. Precise calibration between sample length and X-ray signal gives instantaneous sample length during the burning test, thus, instantaneous burning rate taking its time derivative. Therefore, it is possible to obtain low pressure burning rate and PDL simultaneously in one test at a certain depressurization rate. Results of PDL and low pressure burning rate measurements of a GAP/AP propellant system are hereafter presented and discussed.


Articles with similar content:

FUZZY LOGIC CONTROL OF MATERIAL FLOW IN FLEXIBLE MANUFACTURING SYSTEMS
Flexible Automation and Intelligent Manufacturing, 1997:
Proceedings of the Seventh International FAIM Conference, Vol.0, 1997, issue
William E. Biles, Eman Kamel
Comparison of Methods of the Potential Gross Domestic Product Estimation
Journal of Automation and Information Sciences, Vol.38, 2006, issue 8
A. V. Bakun
INVESTIGATION OF SOLID ROCKET PROPELLANT COMBUSTION BY LASER DOPPLER ANEMOMETRY
International Journal of Energetic Materials and Chemical Propulsion, Vol.3, 1994, issue 1-6
Claudio Zanotti, Angelo Volpi
ANALYTICAL DETERMINATION OF OPTIMUM, TRANSIENT EXPERIMENTS FOR MEASUREMENT OF THERMAL PROPERTIES
International Heat Transfer Conference 3 , Vol.14, 1966, issue
James V. Beck
TRANSIENT BURNING BEHAVIOR OF SOLID PROPELLANTS
International Journal of Energetic Materials and Chemical Propulsion, Vol.3, 1994, issue 1-6
Yeu-Cherng Lu, F. R. Schwam, Y. J. Yim