图书馆订阅: Guest
Begell Digital Portal Begell 数字图书馆 电子图书 期刊 参考文献及会议录 研究收集
传热学
影响因子: 1.199 5年影响因子: 1.155 SJR: 0.267 SNIP: 0.503 CiteScore™: 1.4

ISSN 打印: 1064-2285
ISSN 在线: 2162-6561

卷:
卷 51, 2020 卷 50, 2019 卷 49, 2018 卷 48, 2017 卷 47, 2016 卷 46, 2015 卷 45, 2014 卷 44, 2013 卷 43, 2012 卷 42, 2011 卷 41, 2010 卷 40, 2009 卷 39, 2008 卷 38, 2007 卷 37, 2006 卷 36, 2005 卷 35, 2004 卷 34, 2003 卷 33, 2002 卷 32, 2001 卷 31, 2000 卷 30, 1999 卷 29, 1998 卷 28, 1997

传热学

DOI: 10.1615/HeatTransRes.2018020730
pages 1247-1273

THERMAL PERFORMANCE OF A PIN FIN WITH UNEQUAL CONVECTIVE COEFFICIENTS OVER ITS TIP AND SURFACE

Sunil S. Mehendale
Michigan Technological University, Houghton, Michigan 49931, USA

ABSTRACT

It is generally understood that heat transfer of a fin increases with its length. In cases where the fin tip experiences significantly higher convective coefficients, a situation exists where the heat transfer decreases with its length. Applications of this situation may exist in air conditioning, refrigeration, and electronics cooling. Analytical results for one-dimensional temperature distribution and heat transfer rate are presented for such a pin fin. A critical tip-to-surface coefficient ratio h(= hcrit) depending only on the transverse Biot number Bi exists, for which the heat transfer is independent of length. For "subcritical" conditions (h < hcrit), fin heat transfer increases with length, as is commonly known. In this case, long fins will be necessary for maximizing heat transfer. For "supercritical" situations (h > hcrit), however, the heat transfer rate decreases with length, asymptotically approaching that for an infinitely long fin. Here, short fins will suffice to provide near-maximum heat duty. Compared to the unfinned base exposed to the tip coefficient, subcritical fins will enhance heat transfer; under supercritical situations, they will insulate the surface. However, compared to the finless base exposed to the surface coefficient, fins will always increase heat transfer. If the fin tip is employed to accurately measure the fluid temperature, the dimensionless fin length L must be no less than Lmin, which is a function only of Bi and h/hcrit . An analytical expression for Lmin necessary to keep the relative error within one percent has been developed. Whether the fin is used to enhance heat transfer or measure fluid temperature, the fin cross section should have as high surface area-to-volume ratio as possible.


Articles with similar content:

A STUDY OF HEAT TRANSFER ASSOCIATED WITH THE COOLING OF A HORIZONTAL ROTATING CYLINDER USING AIR JET FLOW
International Heat Transfer Conference 8, Vol.3, 1986, issue
Ximin Zhang, Weiyi Li, Lenyou Wei
Heat Transfer Between an Under-expanded Jet and Plane and Cylindrical Surfaces
International Heat Transfer Conference 12, Vol.15, 2002, issue
Ieuan Owen, Mostafa Rahimi, John Mistry
Heat Transfer through Different Types of Insulation of Superconducting Cable of UNK Model Magnets
ICHMT DIGITAL LIBRARY ONLINE, Vol.0, 1986, issue
Yu. P. Dmitrevsky, S. S. Kozub
MODELLING OF SOME CONSTANT HEAT TRANSFER COEFFICIENT PHASE CHANGE PROBLEMS
International Heat Transfer Conference 9, Vol.4, 1990, issue
P. C. van der Laag, G. C. J. Bart
HEAT TRANSFER ANALYSIS OF AN IMPINGING SLOT JET ON A CONCAVE SURFACE
4th Thermal and Fluids Engineering Conference, Vol.5, 2019, issue
Gilles C. Roy, A. Babineau, Gérard J. Poitras, L.-E. Brizzi