图书馆订阅: Guest
Begell Digital Portal Begell 数字图书馆 电子图书 期刊 参考文献及会议录 研究收集
高温材料处理:国际期刊
ESCI SJR: 0.176 SNIP: 0.48 CiteScore™: 1.3

ISSN 打印: 1093-3611
ISSN 在线: 1940-4360

高温材料处理:国际期刊

DOI: 10.1615/HighTempMatProc.v15.i2.10
pages 87-95

CHARACTERISATION OF AL2O3 PLASMA SPRAYING BY ATOMIC EMISSION SPECTROSCOPY AND NEAR INFRARED PYROMETRY

Ph. Bertrand
C. N. R. S., Institut de Science et de Genie des Materiaux et Procedes B. P. 5, Odeillo, F-66125 Font-Romeu Cedex
J. M. Badie
C. N. R. S., Institut de Science et de Genie des Materiaux et Procedes B. P. 5, Odeillo, F-66125 Font-Romeu Cedex
I. Yu. Smurov
C. N. R. S., Institut de Science et de Genie des Materiaux et Procedes B. P. 5, Odeillo, F-66125 Font-Romeu Cedex; Ecole Nationale d'Ingenieurs de Saint-Etienne, 58 rue Jean Parot, 42023 Saint -Etienne Cedex 2, France
G. Colonges
Projection Plasma Systeme, Z.I. du Colombier, BP 4, 12220 Montbazens

ABSTRACT

Plasma temperature measurement and 2D light intensity mapping of an industrial plasma spraying equipment developed by 2PS (14−45 kW, Ar/H2 plasma, Al2O3 powder) is performed based on atomic emission spectroscopy and near infrared pyrometry. The influence of the process parameter variations onto the plasma electron density with and without Al2O3 powder has been identified. Plasma temperature and electron density are determined by Atomic Emission Spectroscopy (a monochromator with focal length of 320 mm is used, allowing spectra acquisitions on a wide spectral range up to 70 nm) based on the H-beta line broadening in the assumption of plasma equilibrium. A 2D pyrometer (vision zone 10 × 10 mm2) with the 0.860 μm spectral band has been applied to obtain the radiative intensity mapping of the jet. A 1 spot monochromatic pyrometer (in the 1.5 μm spectral range) sighted to the impact area has been used to control in real time the substrate brightness temperature versus process parameters. The following variations of operational conditions were studied: hydrogen flow rate (0 − 15 l/min), powder flow rate (10 − 20 g/min) and current (500 − 700 A), argon flow rate was fixed (70 1/min). It has been found that along the jet axis (up to 40 mm from the nozzle) the temperature and the electron density vary in the range 13,000 − 11,000 K and 1.4 × 1017 − 4 × 1016 cm−3, respectively. The 2D radiation intensity fields are rather sensitive to the variation of current and H2 flow rate and visualize the plasma flow pattern.

REFERENCES

  1. Landes, K., Diagnostics and on-line-control of a plasma spraying process.

  2. Vardelle, M., Vardelle, A., Fauchais, P., and Moreau, C., Pyrometer system for monitoring the particle impact on a substrate during plasma spray process.

  3. Griem, H. R., Spectral Line Broadening by Plasma.

  4. Ignatiev, M., Smurov, I. Y., Flamant, G., Senchenko, V., and Dozhdikov, V., Two-dimensional resolution pyrometer for real-time monitoring of temperature image in laser materials processing.

  5. Ignatiev, M., Smurov, I., Flamant, G., Senchenko, V., Dozhdikov, V., and Bertrand, P., High speed pyrometers for temperature measurements in laser material treatment.


Articles with similar content:

CHARACTERISATION OF AL2O3 PLASMA SPRAYING BY ATOMIC EMISSION SPECTROSCOPY AND NEAR INFRARED PYROMETRY
Progress in Plasma Processing of Materials, 2001, Vol.0, 2001, issue
J. M. Badie, Ph. Bertrand, I. Yu. Smurov, G. Colonges
OPTICAL MEASUREMENTS OF SURFACE TEMPERATURE IN LASER MACHINING
International Heat Transfer Conference 10, Vol.4, 1994, issue
M. Ignatiev, Gilles Flamant, I. Yu. Smurov
RELEVANT PARAMETERS FOR LASER BONDING OF COPPER ON ALUMINA
High Temperature Material Processes: An International Quarterly of High-Technology Plasma Processes, Vol.10, 2006, issue 2
J. C. Labbe, Pierre Lefort, J. Jarrige, S. Menecier
DIAGNOSTICS AND OPTICAL PROPERTIES OF DENSE HELIUM PLASMAS PRODUCED IN FLASHLAMP
Progress in Plasma Processing of Materials, 1999, Vol.1, 1999, issue
L.G. D'yachkov, M. El Bezzari, Yu. K. Kurilenkov, Y. Vitel
Liquid Film Thickness Measurement by the Fiber-Optical Probe
Heat Transfer Research, Vol.29, 1998, issue 6-8
Aleksei R. Evseev