图书馆订阅: Guest
Begell Digital Portal Begell 数字图书馆 电子图书 期刊 参考文献及会议录 研究收集
雾化与喷雾
影响因子: 1.737 5年影响因子: 1.518 SJR: 0.814 SNIP: 1.18 CiteScore™: 2.2

ISSN 打印: 1044-5110
ISSN 在线: 1936-2684

卷:
卷 30, 2020 卷 29, 2019 卷 28, 2018 卷 27, 2017 卷 26, 2016 卷 25, 2015 卷 24, 2014 卷 23, 2013 卷 22, 2012 卷 21, 2011 卷 20, 2010 卷 19, 2009 卷 18, 2008 卷 17, 2007 卷 16, 2006 卷 15, 2005 卷 14, 2004 卷 13, 2003 卷 12, 2002 卷 11, 2001 卷 10, 2000 卷 9, 1999 卷 8, 1998 卷 7, 1997 卷 6, 1996 卷 5, 1995 卷 4, 1994 卷 3, 1993 卷 2, 1992 卷 1, 1991

雾化与喷雾

DOI: 10.1615/AtomizSpr.v9.i5.20
pages 467-482

TRANSIENT 3D ANALYSIS OF A Dl GASOLINE INJECTOR SPRAY

M. A. Comer
Cardiff School of Engineering, Division of Mechanical Engineering and Energy Studies, Cardiff University, Cardiff, U.K.
Phil J. Bowen
Cardiff School of Engineering, The Parade, Cardiff, CF24 3AA, United Kingdom
Colin J. Bates
Cardiff School of Engineering Cardiff University, PO Box 685 Cardiff CF24 3TA, UK
S. M. Sapsford
Ricardo UK, Shoreham Technical Centre, Shoreham-by-Sea, West Sussex, BN43 5FG, United Kingdom
R. J. R. Johns
Ricardo Consulting Engineers Ltd., Bridge Works, Shoreham-by-Sea, West Sussex, U.K.

ABSTRACT

A cycle-resolved, phase Doppler anemometry (PDA) methodology is appraised for the collection and analysis of data from a gasoline fuel injector. A high-pressure swirl injector is utilized, spraying unleaded gasoline into air at ambient pressure and temperature. Results are presented in terms of Sauter mean diameter (SMD) of droplets, three components of velocity, and semiquantitative mass flow rate for the entire flow field.
Spray development is analyzed using time increments of between 0.25 ms and 1 ms over the first 12 ms after injection. High-speed photography confirms the validity of some of the global trends identified, including head vortex development, spray penetration, and needle bounce.
PDA measurements indicate that larger droplets are produced in the early stages of the injection. These populate the head and periphery of the spray cone, which becomes essentially hollow for a period between 0.75 and 2 ms. Smaller droplets in the center of the cone attain velocities in excess of 50 m/s, while those on the edge are entrained by the recirculating head vortex.
During the early injection period, the majority of the liquid mass resides within the "head" and an annular section of the spray, which indicates the hollow cone design. After 3 ms, the spray becomes more homogenous, with little mass flow rate variation across the cone identifiable after 4.5 ms.
The data are finally compared with a standard time-averaged correlation usually utilized for this type of injector. This emphasizes the need for continued effort on transient predictive spray modeling in future direct-injection (DI) gasoline investigations.


Articles with similar content:

CHARACTERISTICS OF THE SPRAY PRODUCED BY THE ATOMIZATION OF AN ANNULAR LIQUID SHEET ASSISTED BY AN INNER GAS JET
Atomization and Sprays, Vol.22, 2012, issue 6
Nicolas Leboucher, Francis Roger, Jean-Louis Carreau
EXPERIMENTAL INVESTIGATION OF GEOMETRIC SCALING ON ATOMIZATION IN A TWO-PHASE GAS/LIQUID SPRAY
Multiphase Science and Technology, Vol.22, 2010, issue 2
Alidad Amirfazli, Mohammad Azizur Rahman, C. E. Ejim, Brian A. Fleck
EXPERIMENTAL STUDY OF SPRAY BREAKUP PHENOMENA IN SMALL-SCALE SIMPLEX ATOMIZERS WITH AND WITHOUT AIR SWIRL
Atomization and Sprays, Vol.28, 2018, issue 4
Muralidhara Suryanarayana Rao, Srinivasan Kothandaraman, Muthuselvan Govindaraj, Kushal D. Ghate, Venkat S. Iyengar, Sundararajan Thirumalachari
EFFERVESCENT ATOMIZATION AT INJECTION PRESSURES IN THE MPa RANGE
Atomization and Sprays, Vol.9, 1999, issue 6
Jay P. Gore, Robert A. Wade, W. A. Eckerle, Jennifer M. Weerts
STUDIES OF GASOLINE DIRECT-INJECTION SPRAYS AT ELEVATED AMBIENT GAS TEMPERATURES AND PRESSURES
Atomization and Sprays, Vol.22, 2012, issue 4
M. Gold, Phil J. Bowen, S. M. Sapsford, Peter J. Kay