图书馆订阅: Guest
Begell Digital Portal Begell 数字图书馆 电子图书 期刊 参考文献及会议录 研究收集
雾化与喷雾
影响因子: 1.737 5年影响因子: 1.518 SJR: 0.814 SNIP: 1.18 CiteScore™: 2.2

ISSN 打印: 1044-5110
ISSN 在线: 1936-2684

卷:
卷 30, 2020 卷 29, 2019 卷 28, 2018 卷 27, 2017 卷 26, 2016 卷 25, 2015 卷 24, 2014 卷 23, 2013 卷 22, 2012 卷 21, 2011 卷 20, 2010 卷 19, 2009 卷 18, 2008 卷 17, 2007 卷 16, 2006 卷 15, 2005 卷 14, 2004 卷 13, 2003 卷 12, 2002 卷 11, 2001 卷 10, 2000 卷 9, 1999 卷 8, 1998 卷 7, 1997 卷 6, 1996 卷 5, 1995 卷 4, 1994 卷 3, 1993 卷 2, 1992 卷 1, 1991

雾化与喷雾

DOI: 10.1615/AtomizSpr.v20.i6.30
pages 513-524

CAVITATION IN NOZZLES OF PLAIN ORIFICE ATOMIZERSWITH VARIOUS LENGTH-TO-DIAMETER RATIOS

Akira Sou
Graduate School of Maritime Sciences, Kobe University, Kobe, Japan
Shigeo Hosokawa
Kansai University
Akio Tomiyama
Graduate School of Engineering, Kobe University, 1-1 Rokkodai-cho, Nada, Kobe, 657-8501, Japan

ABSTRACT

Cavitation in two-dimensional and cylindrical nozzles with various length-to-diameter (L/D) ratios and its effects on liquid jet deformation are investigated by carrying out simultaneous high-speed visualization of the cavitation and jet. The applicability of a modified cavitation number to quantitative prediction of supercavitation formation for nozzles with various L/D ratios is also examined. As a result, the following conclusions are obtained. (1) The modified cavitation number σc can predict supercavitation in nozzles of various shapes and L/D ratios. (2) When cavitation length Lcav is less than twice the nozzle diameter D, the cavitation length normalized by the diameter (Lcav/D), rather than by the nozzle length (Lcav/L), can be expressed as a unique function of σc. (3) Once a cavitation film is formed in long nozzles (L/D ≥ 4), the cavitation zone suddenly extends to near the exit even for very long nozzles (L/D = 8). (4) In short nozzles (L/D = 2), incipient cavitation consisting of tiny bubbles can reach the vicinity of the exit. However, a hydraulic flip instead of a cavitation film is formed even at a low flow rate. (5) In long nozzles (L/D = 8), hydraulic flip does not occur even at very high flow rates, which is preferable for a plain orifice atomizer. (6) Cavitation clouds are shed and collapse near the exit to induce a large deformation of the discharged jet, not only in moderately long (L/D = 4) but also in shorter and longer nozzles.


Articles with similar content:

Experimental Analysis of Non Circular Co-Flow in the Incompressible Coaxial Jets
International Journal of Fluid Mechanics Research, Vol.39, 2012, issue 4
B. T. N. Sridhar, Ponnambalam Manivannan
CRITICAL VELOCITIES AND DROPLET SIZES FOR ENTRAINED SPRAYS FROM MESHED INTERFACE BY CONVECTIVE AIR STREAM
Transport Phenomena in Thermal Engineering. Volume 2, Vol.0, 1993, issue
Kenneth D. Kihm, G. P. "Bud" Peterson, B. H. Kim
INFLUENCE OF NOZZLE EXIT CONDITIONS ON THE NEAR-FIELD MEAN FLOW CHARACTERISTICS OF LOW-ASPECT-RATIO RECTANGULAR JETS
International Journal of Fluid Mechanics Research, Vol.44, 2017, issue 4
Madjid Birouk, Julien Barber, Meghdad Saediamiri
EFFECT OF NOZZLE GEOMETRY ON THE ATOMIZATION AND SPRAY CHARACTERISTICS OF GELLED-PROPELLANT SIMULANTS FORMED BY TWO IMPINGING JETS
Atomization and Sprays, Vol.20, 2010, issue 12
Jong Guen Lee, Syed Fakhri, Richard A. Yetter
CRITICAL EVALUATION OF MOMENTUM FLUX RATIO RELATIVE TO A LIQUID JET IN CROSSFLOW
Atomization and Sprays, Vol.28, 2018, issue 7
Scott Samuelsen, Scott B. Leask, Vincent G. McDonell