图书馆订阅: Guest
Begell Digital Portal Begell 数字图书馆 电子图书 期刊 参考文献及会议录 研究收集
界面现象 及传热
ESCI SJR: 0.146

ISSN 打印: 2169-2785
ISSN 在线: 2167-857X

Open Access

界面现象 及传热

DOI: 10.1615/InterfacPhenomHeatTransfer.2018026089
pages 75-88

INTERACTION OF IMPACTING WATER DROP WITH A HEATED SURFACE AND BREAKUP INTO MICRODROPS

Elizaveta Ya. Gatapova
Kutateladze Institute of Thermophysics, Siberian Branch of Russian Academy of Sciences, 1 Lavrentyev Ave., 630090 Novosibirsk, Russia; Novosibirsk State University, 2 Pirogova Str., 630090 Novosibirsk, Russia
Ekaterina O. Kirichenko
Kutateladze Institute of Thermophysics SB RAS, Novosibirsk, 630090, Russia
Bo-Feng Bai
Xi'an Jiaotong University, Energy and Power Engineering, State Key Laboratory of Multiphase Flow No.28 xianning west road, Xi'an, 710049, China
Oleg A. Kabov
Kutateladze Institute of Thermophysics of the Siberian Branch of the Russian Academy of Sciences, 1, Acad. Lavrentyev Ave., Novosibirsk, 630090, Russia; Institute of Power Engineering, National Tomsk Polytechnic Research University, 7, Usova Street, Tomsk, 634050, Russia; Novosibirsk State University, 2, Pirogova str., Novosibirsk, 630090, Russia

ABSTRACT

Drop impact is important for numerous industrial processes. The recent progress in investigations of drop impact on heated solid surface covers the processes near and above the boiling temperature of the liquid. There is a gap in understanding of drop dynamics for the substrate temperature below the liquid boiling point. We conduct a detailed study of the interaction of the water drop of 10 μl impacting on a heated sapphire plate with a temperature varied within a range of 23–135°C. Characteristic stages of drop interaction with a substrate at various temperatures are identified, namely impact, spreading, rollback, one liquid column splashing, microdrops detachment, formation, stabilization, breakup, boiling, and evaporation. We show that the spreading time and maximal spreading diameter of the droplet are dominated by inertia and practically independent of the temperature. The influence of the temperature on viscosity dissipation, which limits the maximum spreading diameter, is not significant. However, the temperature rise leads to a considerable decrease of the liquid column contact diameter and to an increase of the liquid column height at the splashing stage. It is revealed that the contact line velocity at the rollback stage depends on temperature. Microdrop detachment from the liquid column is observed for a substrate temperature of 60–100°C. Beginning from the substrate temperature of 100°C, the liquid column height is decreased again. The most important observation is the drop breakup into several sessile microdrops just after the spreading for 135°C, which prevents the rollback and rebound. We show the possible importance of the Marangoni force for thin liquid film breakup and detect the presence of microbubbles, which is also potentially important for breakup.


Articles with similar content:

Effect of the Vapor Flow on the Drop Spreading in the Leidenfrost Regime
International Heat Transfer Conference 15, Vol.28, 2014, issue
Guillaume Castanet, Alexandre Labergue, Michel GRADECK, Fabrice Lemoine, Ophelie Caballina
EXPERIMENTAL INVESTIGATION OF THE IMPACT OF AN (APPARENT) YIELD-STRESS MATERIAL
Atomization and Sprays, Vol.15, 2005, issue 1
S. Nigen
SPLASHING PHENOMENA DURING LIQUID DROPLET IMPACT
Atomization and Sprays, Vol.20, 2010, issue 4
Sam S. Yoon, Jie Liu, Richard A. Jepsen, Henry Vu, Guillermo Aguilar
EFFECT OF SOLID SURFACE PROPERTY ON GEOMETRIC VARIATIONS OF MICRO- TO MILLIMETER-SIZED WATER DROPLETS DURING VOLUME REDUCTION PROCESS
Atomization and Sprays, Vol.27, 2017, issue 6
Yukihiro Yonemoto, Tomoaki Kunugi
MODELING TEMPERATURE DISTRIBUTION INSIDE AN EMULSION FUEL DROPLET UNDER CONVECTIVE HEATING: A KEY TO PREDICTING MICROEXPLOSION AND PUFFING
Atomization and Sprays, Vol.26, 2016, issue 6
R. F. Cracknell, Junji Shinjo, J. Xia, L. C. Ganippa, A. Megaritis