Abo Bibliothek: Guest
Digitales Portal Digitale Bibliothek eBooks Zeitschriften Referenzen und Berichte Forschungssammlungen
Heat Transfer Research
Impact-faktor: 0.404 5-jähriger Impact-Faktor: 0.8 SJR: 0.264 SNIP: 0.504 CiteScore™: 0.88

ISSN Druckformat: 1064-2285
ISSN Online: 2162-6561

Volumes:
Volumen 50, 2019 Volumen 49, 2018 Volumen 48, 2017 Volumen 47, 2016 Volumen 46, 2015 Volumen 45, 2014 Volumen 44, 2013 Volumen 43, 2012 Volumen 42, 2011 Volumen 41, 2010 Volumen 40, 2009 Volumen 39, 2008 Volumen 38, 2007 Volumen 37, 2006 Volumen 36, 2005 Volumen 35, 2004 Volumen 34, 2003 Volumen 33, 2002 Volumen 32, 2001 Volumen 31, 2000 Volumen 30, 1999 Volumen 29, 1998 Volumen 28, 1997

Heat Transfer Research

DOI: 10.1615/HeatTransRes.v42.i2.50
pages 165-180

Advanced Aero-Thermal Investigation of High-Pressure Turbine Tip Flows

Peter Vass
Turbomachinery & Propulsion Department, Von Kármán Institute for Fluid Dynamics, Rhode-Saint-Genése, B-1640, Belgium
Tony Arts
Turbomachinery & Propulsion Department, Von Kármán Institute for Fluid Dynamics, Rhode-Saint-Genése, B-1640, Belgium

ABSTRAKT

The present contribution gives an overview of the numerical work performed at the Von Kármán Institute in the framework of the European research program AITEB-2, concerning the numerical investigation of tip gap flows in linear turbomachinery cascades, representatives of high-pressure turbine rotor blade geometries. The primary goal of the project is the simulation of flow and heat transfer on four distinct blade tip geometries in 3D, including the entire internal cooling setup inside a blade, the validation of the results versus the experimental campaign of Hofer et al. [1] and evaluation of the geometries. The paper presents the computations performed on the first tip geometry (TG1 hereinafter) with recessed tip. The geometry and the numerical setup are described in detail, with emphasis on the grid generation and connection method between internal and external flows. Validation is introduced on the most delicate, zero cooling flow case, in which internal flow in the cooling channels is driven exclusively by pressure difference between pressure side tip region and tip gap. The comparison with experiments is performed for one exit Reynolds number (Re = 900,000), and two exit Mach numbers; M = 0.8 (HRLM) and M = 1.1 (HRHM). Flow visualization is performed and set against experimental oil flow visualization; the basic features of the flow topology are analyzed. Typical results of from heat transfer simulations are shown in both test cases.


Articles with similar content:

ADVANCED AERO-THERMAL INVESTIGATION OF HIGH PRESSURE TURBINE TIP FLOWS
ICHMT DIGITAL LIBRARY ONLINE, Vol.0, 2009, issue
Peter Vass, Tony Arts
A NUMERICAL INVESTIGATION OF NEW FILM COOLING HOLE CONFIGURATION AT THE LEADING EDGE OF ASYMMETRICAL TURBINE BLADE: PART B
Computational Thermal Sciences: An International Journal, Vol.8, 2016, issue 5
Mustapha Benabed
NUMERICAL AND EXPERIMENTAL INVESTIGATIONS OF THE AIR FLOW AND HEAT TRANSFER ALONG THE ENTIRE DUCT OF A HYPERSONIC WIND TUNNEL
TsAGI Science Journal, Vol.50, 2019, issue 2
Rashid Anvarovich Davletkil'deev, Alena Sergeevna Rtishcheva, Sergei Mikhailovich Drozdov
Aerothermal study of periodic pulsed jet issuing into a crossflow: application to temperature mixture near wall
ICHMT DIGITAL LIBRARY ONLINE, Vol.0, 2012, issue
Eva Dorignac, Q. Sultan, Matthieu Fenot, Gildas Lalizel
LARGE-SCALED NUMERICAL INVESTIGATION ON FILM COOLING WITH CASCADED DOUBLE JETS
Second Thermal and Fluids Engineering Conference, Vol.4, 2017, issue
Xian Wang, Yanqin Shangguan, Yueming Li