Abo Bibliothek: Guest
Digitales Portal Digitale Bibliothek eBooks Zeitschriften Referenzen und Berichte Forschungssammlungen
Heat Transfer Research
Impact-faktor: 0.404 5-jähriger Impact-Faktor: 0.8 SJR: 0.264 SNIP: 0.504 CiteScore™: 0.88

ISSN Druckformat: 1064-2285
ISSN Online: 2162-6561

Volumes:
Volumen 50, 2019 Volumen 49, 2018 Volumen 48, 2017 Volumen 47, 2016 Volumen 46, 2015 Volumen 45, 2014 Volumen 44, 2013 Volumen 43, 2012 Volumen 42, 2011 Volumen 41, 2010 Volumen 40, 2009 Volumen 39, 2008 Volumen 38, 2007 Volumen 37, 2006 Volumen 36, 2005 Volumen 35, 2004 Volumen 34, 2003 Volumen 33, 2002 Volumen 32, 2001 Volumen 31, 2000 Volumen 30, 1999 Volumen 29, 1998 Volumen 28, 1997

Heat Transfer Research

DOI: 10.1615/HeatTransRes.2018015455
pages 929-948

CONFINED IMPINGING LIQUID JET CHARACTERISTICS OF VAPOR CHAMBER EMBEDDED WITH HEAT SINKS

Paisarn Naphon
Department of Mechanical Engineering, Faculty of Engineering, Srinakharinwirot University, Thailand
Songkran Wiriyasart
Department of Mechanical Engineering, Faculty of Engineering, Srinakharinwirot University, Thailand

ABSTRAKT

The experimental and numerical results of the study of the thermal resistance and fluid flow characteristics of a confined impinging liquid cooling vapor chamber are presented. Experiments are performed to verify the results predicted by the mathematical model. Effects of various parameters, heat source size, material of fin, channel width, and mass flow rate of the coolants on the cooling performance and thermal resistance characteristics are considered. A numerical analysis of a three-dimensional transient model of confined impinging has been carried out to evaluate the thermal and fluid-dynamic performances. By applying the mathematical modeling, the velocity and temperature distributions inside the vapor chamber are presented. Reasonable agreement is obtained between the measured data and the predicted results. These results are useful for the design to improve the thermal performance of the vapor chamber, and also diminished the expense and time of experiments.


Articles with similar content:

HEAT TRANSFER AND OPTIMIZATION STUDIES ON PCM BASED HYBRID HEAT SINKS WITH DISCRETE PROTRUDING HEAT SOURCES
ICHMT DIGITAL LIBRARY ONLINE, Vol.0, 2015, issue
Deepak Saini, Chakravarthy Balaji, S. P. Venkateshan
Enhanced Boiling Heat Transfer in Porous Layers with Application to Electronic Component Cooling
Journal of Enhanced Heat Transfer, Vol.4, 1997, issue 3
A. Ch. Papaioannou, J. C. Statharas, N. D. Konstantinou, Athanasios K. Stubos, Nikolaos K. Kanellopoulos
3D MODELING AND OPTIMIZATION OF A LOOP HEAT PIPE EVAPORATOR
Heat Pipe Science and Technology, An International Journal, Vol.5, 2014, issue 1-4
Valerie Sartre, R. Hodot, Frederic Lefevre, C. Sarno
MODELLING OF HIGH-SPEED JET COOLING ON MICROSCALE
ICHMT DIGITAL LIBRARY ONLINE, Vol.0, 2017, issue
Yoav Peles, Ashwin Kumar Vutha, Gennady Ziskind, Yingying Wang, Tomer Rozenfeld
HEAT TRANSFER OF IMPINGING SEAWATER SPRAY AND ICE ACCUMULATION ON MARINE VESSEL SURFACES
Heat Transfer Research, Vol.48, 2017, issue 17
Yuri S. Muzychka, G. F. Naterer, Alireza R. Dehghani-Sanij