Abo Bibliothek: Guest
Digitales Portal Digitale Bibliothek eBooks Zeitschriften Referenzen und Berichte Forschungssammlungen
Heat Transfer Research
Impact-faktor: 0.404 5-jähriger Impact-Faktor: 0.8 SJR: 0.264 SNIP: 0.504 CiteScore™: 0.88

ISSN Druckformat: 1064-2285
ISSN Online: 2162-6561

Volumes:
Volumen 50, 2019 Volumen 49, 2018 Volumen 48, 2017 Volumen 47, 2016 Volumen 46, 2015 Volumen 45, 2014 Volumen 44, 2013 Volumen 43, 2012 Volumen 42, 2011 Volumen 41, 2010 Volumen 40, 2009 Volumen 39, 2008 Volumen 38, 2007 Volumen 37, 2006 Volumen 36, 2005 Volumen 35, 2004 Volumen 34, 2003 Volumen 33, 2002 Volumen 32, 2001 Volumen 31, 2000 Volumen 30, 1999 Volumen 29, 1998 Volumen 28, 1997

Heat Transfer Research

DOI: 10.1615/HeatTransRes.v41.i8.50
pages 849-865

Trailing Edge Film Cooling of Gas Turbine Airfoils — Effects of Ejection Lip Geometry on Film Cooling Effectiveness and Heat Transfer

Tim Horbach
Institut fuer Thermische Stroemungsmaschinen (ITS), Karlsruhe Institute of Technology (KIT), 76131 Karlsruhe, Germany
Achmed Schulz
Institut fuer Thermische Stroemungsmaschinen (ITS), Karlsruhe Institute of Technology (KIT), 76131 Karlsruhe, Germany
Hans-Jorg Bauer
Institut fuer Thermische Stroemungsmaschinen (ITS), Karlsruhe Institute of Technology (KIT), 76131 Karlsruhe, Germany

ABSTRAKT

The present paper concentrates on trailing edge film cooling of modern high-pressure turbine blades using cooling ejection through planar slots with a pressure side cutback. The experimental test section consists of a generic scaled-up trailing edge model. The effects of different geometric configurations on the structure and the performance of the cooling film are investigated in terms of film cooling effectiveness, heat transfer coefficients, and discharge behavior. The interaction between an internal turbulator array of ribs with the ejection slot lip is of major interest. Different designs of the cooling ejection lip are applied. Four different ratios of lip thickness to ejection slot height (t/H = 0.2, 0.5, 1.0, 1.5) are investigated, as well as three different lip contours representing typical manufacturing imperfections and wear. The experiments are performed at engine-realistic density ratios. The blowing ratios are varied between 0.2 < M < 1.25. The results show a strong dependency on ejection lip thickness and only marginal changes when the lip shape is varied.


Articles with similar content:

TRAILING EDGE FILM COOLING OF GAS TURBINE AIRFOILS – EFFECTS OF EJECTION LIP GEOMETRY ON FILM COOLING EFFECTIVENESS AND HEAT TRANSFER
ICHMT DIGITAL LIBRARY ONLINE, Vol.0, 2009, issue
Achmed Schulz, Hans-Jorg Bauer, Tim Horbach
LES OF FILM COOLING EFFICIENCY FOR DIFFERENT HOLE SHAPES
TSFP DIGITAL LIBRARY ONLINE, Vol.5, 2007, issue
Peter Renze, Wolfgang Schroder, Matthias Meinke
NUMERICAL INVESTIGATION OF FILM-COOLING EFFECTIVENESS DOWNSTREAM OF A MICRO RAMP
Computational Thermal Sciences: An International Journal, Vol.10, 2018, issue 2
Zakaria Mansouri, Abbes Azzi, Hamza Khamane
Large-Eddy Simulations of trailing-edge cutback film cooling at low blowing ratio
ICHMT DIGITAL LIBRARY ONLINE, Vol.0, 2009, issue
Hayder Schneider, Dominic von Terzi, Hans-Jorg Bauer
INTERACTIONS OF COMBUSTOR WALL AND FILM COOLING ON ENDWALL FOR A FIRST-STAGE VANE
Second Thermal and Fluids Engineering Conference, Vol.4, 2017, issue
Zhao Liu, Xing Yang, Zhenping Feng, Zhansheng Liu