Abo Bibliothek: Guest
Digitales Portal Digitale Bibliothek eBooks Zeitschriften Referenzen und Berichte Forschungssammlungen
Heat Transfer Research
Impact-faktor: 1.199 5-jähriger Impact-Faktor: 1.155 SJR: 0.267 SNIP: 0.503 CiteScore™: 1.4

ISSN Druckformat: 1064-2285
ISSN Online: 2162-6561

Volumes:
Volumen 51, 2020 Volumen 50, 2019 Volumen 49, 2018 Volumen 48, 2017 Volumen 47, 2016 Volumen 46, 2015 Volumen 45, 2014 Volumen 44, 2013 Volumen 43, 2012 Volumen 42, 2011 Volumen 41, 2010 Volumen 40, 2009 Volumen 39, 2008 Volumen 38, 2007 Volumen 37, 2006 Volumen 36, 2005 Volumen 35, 2004 Volumen 34, 2003 Volumen 33, 2002 Volumen 32, 2001 Volumen 31, 2000 Volumen 30, 1999 Volumen 29, 1998 Volumen 28, 1997

Heat Transfer Research

DOI: 10.1615/HeatTransRes.2018021461
pages 865-880

EXPERIMENTAL STUDY OF ADIABATIC COOLING EFFECTIVENESS ON AN EFFUSION COOLED TEST PLATE WITH MACHINED RING GEOMETRIES

Jesuraj Felix
CSIR-National Aerospace Laboratories, Bangalore, Karnataka, India
Raghavan Rajendran
CSIR-National Aerospace Laboratories, Bangalore, Karnataka, India
Gottekre Narayanappa Kumar
Department of Mechanical Engineering, NITK, Surathkal, India
Yepuri Giridhara Babu
CSIR-National Aerospace Laboratories, Bangalore, Karnataka, India

ABSTRAKT

The present study deals with experimental investigation of adiabatic cooling effectiveness on an effusion cooled test plate with machined ring geometries. Initial tests were performed on an effusion cooling holes. The cooling effectiveness at the beginning of effusion holes is lower, and it increases in the flow direction mainly due to the additive effect of film cooling effectiveness of the effusion cooling geometry. Subsequent tests were done with machined ring geometries fixed ahead of effusion cooling hole geometry to improve the cooling effectiveness before the beginning of effusion cooling holes. These machined ring geometries act as a wall jet and reduce the hot side heat load by film cooling performance. Tests were performed at a coolant to mainstream density ratio of 1.3 and at blowing ratios ranging from 0.5 to 2.5. Increase in the blowing ratio shows an increase in the cooling effectiveness. Comparison results show that the adiabatic cooling effectiveness increases significantly before the effusion cooling holes in the presence of machined ring geometries at all blowing ratios.


Articles with similar content:

EFFECT OF ANTI-VORTEX HOLE ANGLE ON THE FILM COOLING EFFECTIVENESS
Heat Transfer Research, Vol.48, 2017, issue 6
Jae Su Kwak, Younggi Moon, Soon Sang Park, Jung Shin Park
A NUMERICAL INVESTIGATION OF NEW FILM COOLING HOLE CONFIGURATION AT THE LEADING EDGE OF ASYMMETRICAL TURBINE BLADE: PART B
Computational Thermal Sciences: An International Journal, Vol.8, 2016, issue 5
Mustapha Benabed
EFFECTS OF HOLE GEOMETRY AND CURVED SURFACE ON FILM COOLING EFFECTIVENESS AND HEAT TRANSFER COEFFICIENT MEASURED WITH COMPENSATION OF THREE-DIMENSIONAL HEAT CONDUCTION
International Heat Transfer Conference 16, Vol.10, 2018, issue
Akira Murata, Kaoru Iwamoto, Yushi Maruyama, Jingzu Yee, Yoji Okita, Shohei Yamamoto
EXPERIMENTAL STUDY ON THE EFFECT OF CONCAVE AND CONVEX CURVATURES ON FILM COOLING EFFECTIVENESS
International Heat Transfer Conference 9, Vol.6, 1990, issue
Taik Sik Lee, Sang Woo Lee, Joon Sik Lee
ROCK-BREAKING CHARACTERISTICS FOR THE COMBINED SWIRLING AND STRAIGHT SUPERCRITICAL CARBON DIOXIDE JET UNDER AMBIENT PRESSURE
Atomization and Sprays, Vol.26, 2016, issue 7
Kewen Peng, Huanpeng Chi, Shouceng Tian, Haizhu Wang, Gensheng Li, Qilong Zhang, Zhaokun Li