Abo Bibliothek: Guest
Digitales Portal Digitale Bibliothek eBooks Zeitschriften Referenzen und Berichte Forschungssammlungen
Journal of Enhanced Heat Transfer
Impact-faktor: 1.406 5-jähriger Impact-Faktor: 1.075 SJR: 0.287 SNIP: 0.653 CiteScore™: 1.2

ISSN Druckformat: 1065-5131
ISSN Online: 1563-5074

Volumes:
Volumen 27, 2020 Volumen 26, 2019 Volumen 25, 2018 Volumen 24, 2017 Volumen 23, 2016 Volumen 22, 2015 Volumen 21, 2014 Volumen 20, 2013 Volumen 19, 2012 Volumen 18, 2011 Volumen 17, 2010 Volumen 16, 2009 Volumen 15, 2008 Volumen 14, 2007 Volumen 13, 2006 Volumen 12, 2005 Volumen 11, 2004 Volumen 10, 2003 Volumen 9, 2002 Volumen 8, 2001 Volumen 7, 2000 Volumen 6, 1999 Volumen 5, 1998 Volumen 4, 1997 Volumen 3, 1996 Volumen 2, 1995 Volumen 1, 1994

Journal of Enhanced Heat Transfer

DOI: 10.1615/JEnhHeatTransf.2011003265
pages 389-401

LOCAL HEAT TRANSFER OF JET IMPINGEMENT COOLING WITH FILM EXTRACTION FLOW IN A ROTATING CAVITY

Kai Wang
Key Laboratory of Molecular Virology & Immunology, Institut Pasteur of Shanghai, Shanghai Institutes for Biological Sciences, Chinese Academy of Sciences, Shanghai 200025, China
Guoqiang Xu
National Key Laboratory of Science and Technology on Aero-Engines, School of Jet Propulsion, Beihang University, Beijing, 100191, China; School of Energy Science and Engineering, Harbin institute of Technology, Harbin, 150001, China
Zhi Tao
National Key Laboratory of Science and Technology on Aero-Engine Aero-thermodynamics The Collaborative Innovation Center for Advanced Aero-Engine of China Beihang University Beijing 100191, China
Jining Sun
National Key Laboratory of Science and Technology on Aero-Engines, School of Jet Propulsion, Beihang University, Beijing, 100191, China
Hongwu Deng
National Key Laboratory of Science and Technology on Aero-Engines, School of Jet Propulsion, Beihang University, Beijing, 100191, China

ABSTRAKT

An experimental investigation was carried out to examine the heat transfer characteristics on impingement cooling with extraction flow in a rotating cavity. Two H/d configurations of 3.0 and 6.0 were conducted. The Reynolds number based on the inlet velocity of the jet air and the diameter of the impingement hole was fixed at 2000. The test model rotated at five different speeds, 0, 200, 400, 600, and 800 rpm, in two reversal directions, respectively. The local heat transfer coefficient on the target surface was measured by a transient method with thermochromic liquid crystal. Experimental result reveals that the jet flow could be bent by the Coriolis force and consequently the heat transfer would be weakened by rotation. The heat transfer coefficient of H/d = 3 configuration is higher than that of H/d = 6 configuration for either stationary or rotational conditions. For the structure of H/d = 6.0, the stagnation point has an offset of 1.5d due to the bending of the jet flow. Compared to the stationary results, the maximum of the local heat transfer coefficient is reduced by 38.3% and the averaged heat transfer coefficient is reduced by 44.5% at 800 rpm. For the structure of H/d = 3.0, the offset of the stagnation point is small, but the spreading rate of the jet core is enhanced by rotation. Although not as strongly as the structure of H/d = 6.0, the heat transfer is still weakened by rotation. The maximum of local heat transfer coefficient is decreased 29.2% and average heat transfer coefficient is decreased 27.8% at 800 rpm compared to those at 0 rpm.


Articles with similar content:

EXPERIMENTAL INVESTIGATION OF ORTHOGONAL MULTI-JET AIR IMPINGEMENT ON COMBINED DIMPLE AND PIN-FIN HEAT SINK
Proceedings of the 24th National and 2nd International ISHMT-ASTFE Heat and Mass Transfer Conference (IHMTC-2017), Vol.0, 2017, issue
S. S. Vasekar, Sunil V. Dingare, Sandeep S. Kore
Effects of Surface Geometry and Blowing Ratio on Film Cooling Performance at Airfoil Trailing Edge Investigated by Using Large Eddy Simulation
International Heat Transfer Conference 15, Vol.20, 2014, issue
Akira Murata, Kaoru Iwamoto, Ena Mori
THE EFFECT OF DIFFERENT COOLING UNIT CONFIGURATIONS AND COOLING TEMPERATURES ON GLASS TEMPERING QUALITY
Atomization and Sprays, Vol.26, 2016, issue 10
Mustafa Golcu, Mehmet Akcay, Hilmi Yazici, Yakup Sekmen
Large eddy simulation of the effects of rotation on heat transfer in a ribbed channel
International Heat Transfer Conference 12, Vol.10, 2002, issue
Richard H. Pletcher, Joon Sang Lee, Yang Liu
NUMERICAL STUDY ON FLOW AND HEAT TRANSFER IN A RECTANGULAR CHANNEL WITH 45 DEG RIB TURBULATORS AND BLEED HOLES
Journal of Enhanced Heat Transfer, Vol.19, 2012, issue 5
Ya Jun Song, Zhong Yang Shen, Yong Hui Xie, Di Zhang