Abo Bibliothek: Guest
Digitales Portal Digitale Bibliothek eBooks Zeitschriften Referenzen und Berichte Forschungssammlungen
Journal of Enhanced Heat Transfer
Impact-faktor: 1.406 5-jähriger Impact-Faktor: 1.075 SJR: 0.287 SNIP: 0.653 CiteScore™: 1.2

ISSN Druckformat: 1065-5131
ISSN Online: 1563-5074

Volumes:
Volumen 27, 2020 Volumen 26, 2019 Volumen 25, 2018 Volumen 24, 2017 Volumen 23, 2016 Volumen 22, 2015 Volumen 21, 2014 Volumen 20, 2013 Volumen 19, 2012 Volumen 18, 2011 Volumen 17, 2010 Volumen 16, 2009 Volumen 15, 2008 Volumen 14, 2007 Volumen 13, 2006 Volumen 12, 2005 Volumen 11, 2004 Volumen 10, 2003 Volumen 9, 2002 Volumen 8, 2001 Volumen 7, 2000 Volumen 6, 1999 Volumen 5, 1998 Volumen 4, 1997 Volumen 3, 1996 Volumen 2, 1995 Volumen 1, 1994

Journal of Enhanced Heat Transfer

DOI: 10.1615/JEnhHeatTransf.v16.i4.20
pages 331-350

Density-Wave Flow Oscillations in a Water Boiling Horizontal Tube with Inserts

Sendogan Karagoz
Department of Mechanical Engineering, Ataturk University, TR-25240 Erzurum, Turkey
Suleyman Karsli
Department of Mechanical Engineering, Faculty of Engineering, Ataturk University, TR-25300 Erzurum, Turkey
Mehmet Yilmaz
Department of Mechanical Engineering, Faculty of Engineering, Ataturk University, Turkey
Omer Comakli
Department of Mechanical Engineering, Ataturk University, TR-25240 Erzurum, Turkey

ABSTRAKT

Density-wave type oscillations are one of the main types of two-phase flow dynamic oscillations frequently encountered in industrial thermal-hydraulic systems. These oscillations are caused by the dynamic interaction between flow rates, density distribution, and pressure drop distribution within the system, and are high-frequency oscillations. To avoid or control density-wave oscillations is of vital importance for two-phase systems, since they can induce thermal oscillations, accelerating the thermal fatique of the tube and finally resulting in burnout damage. In this study, an experimental investigation on two-phase flow density-wave type instabilities in a horizontal pipe with inserts was conducted. Four different heat transfer surface configurations containing one bare tube and three different enhancement inserts were used. The point on the characteristic curve, where pure density-wave oscillations started, changed with the tube configurations. This point was near the middle of the characteristic curve for the smooth tube, whereas it went towards the maximum point of the characteristic curve in the tubes with inserts. The amplitudes and periods of the density-wave type oscillations were lower than those of the pressure-drop type oscillations. By comparing the bare tube and the tubes with inserts on the basis of density-wave type oscillations, it was observed that the amplitudes and periods for the tube configurations with inserts were higher than those of the bare tube. There was no important difference among the tubes with inserts on the basis of density-wave type oscillations.


Articles with similar content:

Two Phase Flow Patterns and Boiling Heat Transfer in Tubes Containing Helical Wire Inserts --Part II - Critical Heat Flux Studies
Journal of Enhanced Heat Transfer, Vol.4, 1997, issue 4
J. Lan, J. Weisman, Peter J. Disimile
Flow Boiling Heat Transfer Coefficient In Minichannels − Correlation and Trends
International Heat Transfer Conference 12, Vol.41, 2002, issue
Mark E. Steinke, Satish G. Kandlikar
REVIEW OF CRITICAL HEAT FLUX IN A VERTICALLY DOWNWARD TWO PHASE FLOW
Proceedings of the 24th National and 2nd International ISHMT-ASTFE Heat and Mass Transfer Conference (IHMTC-2017), Vol.0, 2017, issue
Rajeshwar Sripada, Veeredhi Vasudeva Rao
POOL BOILING HEAT TRANSFER FROM PLAIN AND FINNED TUBES TO PROPANE AND PROPYLENE
International Heat Transfer Conference 9, Vol.2, 1990, issue
Heiko Schomann, Dieter Gorenflo, Werner Rott , Peter Sokol, Peter Blein
The Effect of Augmented Surfaces on Two-Phase Flow Instabilities in a Horizontal System
Journal of Enhanced Heat Transfer, Vol.2, 1995, issue 4
Omer Comakli, F. Widmann, Sadik Kakac, Y. Ding, Claudia O. Gavrilescu