Abo Bibliothek: Guest
Digitales Portal Digitale Bibliothek eBooks Zeitschriften Referenzen und Berichte Forschungssammlungen
High Temperature Material Processes: An International Quarterly of High-Technology Plasma Processes
SJR: 0.176 SNIP: 0.48 CiteScore™: 1.3

ISSN Druckformat: 1093-3611
ISSN Online: 1940-4360

High Temperature Material Processes: An International Quarterly of High-Technology Plasma Processes

DOI: 10.1615/HighTempMatProc.v14.i4.80
pages 379-388

PLASMA SPRAYING OF BORON CARBIDE USING TERNARY GAS MIXTURES

S. Janisson
CEA/DAM Le Ripault, BP 16 - 37260 Monts - France
Armelle Vardelle
ENSIL, ESTER Technopole, 87068 Limoges - France
Michel Vardelle
LMCTS-URA 320, University of Limoges, 123 Avenue Albert Thomas -87060 Limoges Cedex - France
Pierre Fauchais
Laboratoire Sciences des Procedes Ceramiques et de Traitements de Surface UMR CNRS 6638 University of Limoges 123 avenue Albert Thomas, 87060 LIMOGES - France
Erick Meillot
CEA/DAM Le Ripault, BP 16 - 37260 Monts - France

ABSTRAKT

Materials which exhibit high specific heat and melting enthalpy combined with a low density, like boron carbide B4C, are difficult to melt by plasma spraying under standard spray conditions. Moreover, the injection of this low-density powder in the plasma jet is critical, especially when fine particles are used. The optimization of the plasma-forming gas composition may make the penetration of the particles in the gas flow easier, and improve their melting state. This paper presents an investigation of the effect of the composition of ternary gas mixtures of argon, helium and hydrogen on B4C particles heating and acceleration. The particle injection and the resulting spray pattern in the jet were controlled by using a 1D imaging technique. The particle velocity distribution was measured with a laser Doppler anemometer and the particle overall temperature with a high-speed pyrometer.

REFERENZEN

  1. Janisson, S., Meillot, E., Vardelle, A., Coudert, J. F., Pateyron, B., and Fauchais, P. , Plasma Spraying Using Ar-He-H2 Ternary Gas Mixtures.

  2. Swank, W. D., Fincke, J. R., and Haggard, D. C. , A Particle Temperature Sensor for Monitoring and Control of the Thermal Spray Process.

  3. Pateyron, B. and Delluc, G. , ADEP - Databank of University of Limoges and CNRS.


Articles with similar content:

PLASMA SPRAYING OF BORON CARBIDE USING TERNARY GAS MIXTURES
Progress in Plasma Processing of Materials, 1999, Vol.1, 1999, issue
Michel Vardelle, Erick Meillot, S. Janisson, Pierre Fauchais, Armelle Vardelle
On-Line Process Control in Melt Spraying Using Phase-Doppler Anemometry
International Journal of Fluid Mechanics Research, Vol.24, 1997, issue 4-6
J. Raimann, Joachim Domnick, M.-S. Cabot, Alain Berlemont, G. Wolf
RECENT DEVELOPMENTS IN THERMAL SPRAYING FOR IMPROVED COATING CHARACTERISTICS AND NEW APPLICATIONS/ PROCESS CONTROLS AND SPRAY PROCESSES
High Temperature Material Processes: An International Quarterly of High-Technology Plasma Processes, Vol.8, 2004, issue 1
Ghislain Montavon
IN-FLIGHT MEASUREMENT OF PARTICLE SIZE AND VELOCITY IN A RADIO FREQUENCY PLASMA TORCH
Progress in Plasma Processing of Materials, 1999, Vol.1, 1999, issue
S. Nguyen-Kuok, Jacques Amouroux, F. Krayem, Sergey V. Dresvin, Daniel Morvan, E. Francke
PROCESS MODELLING AND -CONTROL OF ATMOSPHERIC PLASMA SPRAYING OF ALUMINA COATINGS
Progress in Plasma Processing of Materials, 1997, Vol.1, 1997, issue
F. Ladru , K. D. Landes, U. Eritt, W. Mayr, A. Reusch, Erick Lugscheider