Abo Bibliothek: Guest
Digitales Portal Digitale Bibliothek eBooks Zeitschriften Referenzen und Berichte Forschungssammlungen
High Temperature Material Processes: An International Quarterly of High-Technology Plasma Processes
SJR: 0.176 SNIP: 0.48 CiteScore™: 1.3

ISSN Druckformat: 1093-3611
ISSN Online: 1940-4360

High Temperature Material Processes: An International Quarterly of High-Technology Plasma Processes

DOI: 10.1615/HighTempMatProc.v7.i2.100
11 pages

INFLUENCE OF DC PLASMA PREHEATING ON OXIDE LAYERS FORMED BY FURNACE HEATING ON LOW CARBON STEEL SUBSTRATES AND RESULTING ADHESION/COHESION OF ALUMINA COATINGS

S. Valette
SPCTS - Science des precedes Ceramique et de Traitements de Surface - UMR CNRS 6638 - University of Limoges -123 Avenue Albert Thomas - 87060 Limoges Cedex - France
Alain Denoirjean
Equipe Plasma Laser Matériaux, ESA CNRS 6015, 87060 Limoges Cedex, France
Pierre Lefort
Laboratoire Science des Precedes Ceramiques et Traitements de Surface UMR CNRS 6638 123 Avenue Albert-Thomas F-87060 Limoges Cedex, France
Pierre Fauchais
Laboratoire Sciences des Procedes Ceramiques et de Traitements de Surface UMR CNRS 6638 University of Limoges 123 avenue Albert Thomas, 87060 LIMOGES - France

ABSTRAKT

In plasma spraying the preheating of low carbon steel substrates (X40) with a rough surface resulting from grit blasting, has received an increased interest because it promotes the adhesion and cohesion (A/C) of alumina coatings. Earlier works have reported the generation of a duplex Fе3O4/Fе2O3 layer after preheating by the d.c. plasma jet. Improved A/C values were obtained for an increase in Fе3O4 content in the oxide layer. Much improved adherence values were achieved with alumina spayed on Fe1-xO layers. In this case, the Adhesion/cohesion values obtained on smooth substrate (Ra ~ 0.1 mm) were good (~ 40 MPa) and close to those obtained on rough ones (Ra ~ 5 mm). First the time evolution of the Fe1-xO layer thickness and morphology produced in a controlled atmosphere furnace was studied. Then the influence of the plasma preheating of the wilstite layers was studied by SEM, and XRD analyses. XRD analysis results indicated a slight variation in the oxide phases depending on the preheating cycles. Fе3O4 was found to increase when a decomposition of Fe1-xO into Fе3O4 was observed.


Articles with similar content:

INFLUENCE OF DC PLASMA PREHEATING ON OXIDE LAYERS FORMED BY FURNACE HEATING ON LOW CARBON STEEL SUBSTRATES AND RESULTING ADHESION/COHESION OF ALUMINA COATINGS
Progress in Plasma Processing of Materials, 2003, Vol.0, 2003, issue
Pierre Lefort, S. Valette, Alain Denoirjean, Pierre Fauchais
CATALYTIC DECOMPOSITION OF H2O2 USING FeCrAl METALLIC FOAM−BASED CATALYSTS
International Journal of Energetic Materials and Chemical Propulsion, Vol.10, 2011, issue 4
C. Augustin, K. Farhat, Yann Batonneau, Charles J. Kappenstein, Rachid Amrousse
EFFECTS OF FLUORINE-CONTAINING SPECIES ON THE IGNITION AND COMBUSTION OF BORON PARTICLES: EXPERIMENT AND THEORY
International Journal of Energetic Materials and Chemical Propulsion, Vol.5, 2002, issue 1-6
Carl Gotzmer, Abdullah Ulas
INFLUENCE OF SUBSTRATE SURFACE OXIDATION STAGE ON THE MORPHOLOGY AND FLATTENING OF SPLATS
High Temperature Material Processes: An International Quarterly of High-Technology Plasma Processes, Vol.7, 2003, issue 2
J. C. Labbe, A. A. Syed, Alain Denoirjean, Pierre Fauchais, P. Denoirjean
FABRICATION AND CHARACTERIZATION OF AN AL/CR2O3/ETN ENERGETIC NANOCOMPOSITE VIA A SOL-GEL METHODOLOGY
International Journal of Energetic Materials and Chemical Propulsion, Vol.16, 2017, issue 4
Dan Song, Zhaoyang Song, Xiaolan Song, Yi Wang