Impact-faktor:
1.016
5-jähriger Impact-Faktor:
1.194
SJR:
0.554
SNIP:
0.68
CiteScore™:
1.18
ISSN Druckformat: 1543-1649
Volumes:
|
International Journal for Multiscale Computational Engineering
DOI: 10.1615/IntJMultCompEng.2011002379
pages 117-130 IS IT NECESSARY TO INCLUDE BIARTICULAR EFFECTS WITHIN JOINT TORQUE REPRESENTATIONS OF KNEE FLEXION AND KNEE EXTENSION?
Mark A. King
School of Sport, Exercise and Health Sciences, Loughborough University, Loughborough LE11 3TU, United Kingdom
M. G. C. Lewis
School of Sport, Exercise and Health Sciences, Loughborough University, Loughborough LE11 3TU, United Kingdom
M. R. Yeadon
School of Sport, Exercise and Health Sciences, Loughborough University, Loughborough LE11 3TU, United Kingdom ABSTRAKTThe purpose of this study was to consider whether it is necessary for biarticular effects to be accounted for in subject-specific representations of maximal voluntary knee extension and knee flexion torques. Isovelocity and isometric knee torques were measured on a single participant at three different hip angles using a Contrex MJ dynamometer. Maximal voluntary torque was represented by a 19-parameter two-joint function of knee and hip joint angles and angular velocities with the parameters determined by minimizing a weighted rms difference between measured torques and the two-joint function. The weighted rms difference between the two-joint function and the measured knee flexion torques was 14 Nm or 9% of maximum torque, while for knee extension the difference was 26 Nm or 9% of maximum torque. The two-joint representation was shown to be more accurate than an existing single-joint representation for torques measured at hip angles other than those used to derive the single-joint function parameter values. The differences between the traditionally used single-joint representation and the measured knee flexion and knee extension torques were largest for the most extended hip joint angle (15 and 18% of maximum torque, respectively), while the corresponding differences for the two-joint function were 9% and 8% of maximum torque. It is concluded that a two-joint function can account for changes in knee flexion and knee extension joint torques due to both monoarticular and biarticular muscles over a range of both hip and knee angles, and this has the potential to improve the biofidelity of whole-body subject-specific torque-driven simulation models. REFERENZEN
Articles with similar content:
Treatment of Neuromuscular Scoliosis with Posterior Spinal Fusion Using the Galveston Procedure: Retrospective of Eight Years of Experience with Unit Rod Instrumentation
Journal of Long-Term Effects of Medical Implants, Vol.22, 2012, issue 1 Styles L. Bertrand, Haitao Zhou, Fredrick O'Neal Gregg
Evaluation and Management of Metal Hypersensitivity in Total Joint Arthroplasty: A Systematic Review
Journal of Long-Term Effects of Medical Implants, Vol.24, 2014, issue 1 Wesley H Mayes, Tony H Tzeng, Khaled J. Saleh, William M. Mihalko, Alice Tzeng, Michael Amini
What are the Risk Factors for Hardware Removal after Tibia or Fibula Fracture?
Journal of Long-Term Effects of Medical Implants, Vol.25, 2015, issue 4 Julio J. Jauregui, Matthew R. Boylan, Paul W. Perdue, Yoseph A. Rosenbaum, Dean C. Perfetti, Bhaveen V. Kapadia, Carl B. Paulino
Dynamic Condylar Screw as a Solution to Operative Dilemma in Early Sub-Trochanteric Fracture Following Cannulated Screw Fixation for Slipped Capital Femoral Epiphysis: A Case Report
Journal of Long-Term Effects of Medical Implants, Vol.22, 2012, issue 1 Raghavendra Prasad Sidaginamale, L. Zolcze, P. Fadero, Alexandros P. Apostolopoulos
Atraumatic Bilateral Quadriceps Tendon Rupture in a Patient with Hypothyroidism
Journal of Long-Term Effects of Medical Implants, Vol.28, 2018, issue 4 David Bird Johnson, Jacob J. Triplet, Benjamin C. Taylor, Benjamin Umbel |
Digitales Portal | Digitale Bibliothek | eBooks | Zeitschriften | Referenzen und Berichte | Forschungssammlungen |