Abo Bibliothek: Guest
Digitales Portal Digitale Bibliothek eBooks Zeitschriften Referenzen und Berichte Forschungssammlungen
Atomization and Sprays
Impact-faktor: 1.737 5-jähriger Impact-Faktor: 1.518 SJR: 0.814 SNIP: 1.18 CiteScore™: 2.2

ISSN Druckformat: 1044-5110
ISSN Online: 1936-2684

Volumes:
Volumen 30, 2020 Volumen 29, 2019 Volumen 28, 2018 Volumen 27, 2017 Volumen 26, 2016 Volumen 25, 2015 Volumen 24, 2014 Volumen 23, 2013 Volumen 22, 2012 Volumen 21, 2011 Volumen 20, 2010 Volumen 19, 2009 Volumen 18, 2008 Volumen 17, 2007 Volumen 16, 2006 Volumen 15, 2005 Volumen 14, 2004 Volumen 13, 2003 Volumen 12, 2002 Volumen 11, 2001 Volumen 10, 2000 Volumen 9, 1999 Volumen 8, 1998 Volumen 7, 1997 Volumen 6, 1996 Volumen 5, 1995 Volumen 4, 1994 Volumen 3, 1993 Volumen 2, 1992 Volumen 1, 1991

Atomization and Sprays

DOI: 10.1615/AtomizSpr.2013006939
pages 343-361

THREE-DIMENSIONAL INVESTIGATIONS OF FLOW CHARACTERISTICS IN A DIESEL NOZZLE

Weidi Huang
School of Automotive Studies, Tongji University, Shanghai 200092, China
Ya Gao
School of Automotive Studies, Tongji University, Shanghai 200092, China
Zhilong Li
Tongji University
Liguang Li
Tongji University
Zhengbai Liu
Dongfeng Motor Corporation, Wuhan 430056, China
Zhijun Wu
School of Automotive Studies, Tongji University, Shanghai 200092, China

ABSTRAKT

Simulation investigations of flow characteristic in diesel nozzles are basically performed using the simplified and idealized geometry models. Therefore, these simulations are essentially two-dimensional (2D), and unavoidably have deviations from real flow characteristics due to lack of three-dimensional (3D) geometry information. In this study, based on the high energy x-ray CT scan, the inner nozzle structures are measured in detail, and the measurement results are applied to generate the 3D computational meshes. The results of the 2D and the 3D simulations are compared to see the effect of the 3D simulation on the flow characteristics in the nozzles. The investigation results show that because of the rough surface and uneven distributions of geometry parameters in the azimuthal direction of the nozzle orifice revealed by the CT scan, the differences of the flow characteristics between the 2D and the 3D simulations are obvious. They exist at the orifice inlet, the orifice outlet, and along the orifice axis. The improvement of evenness of geometry parameter distributions can reduce the differences between the 2D and the 3D simulations. The 3D computational mesh, which contains more geometry parameter information than the 2D one, can reveal details of the influences of geometry parameters on the internal flow of nozzle, and gain more precise simulation results and insight into the flow characteristics under the real nozzle conditions.


Articles with similar content:

NEAR FIELD VISUALIZATION OF DIESEL SPRAY FOR DIFFERENT NOZZLE INCLINATION ANGLES IN NON-VAPORIZING CONDITIONS
Atomization and Sprays, Vol.27, 2017, issue 3
Alberto Viera, Raul Payri, Pedro Marti-Aldaravi, Gabriela Bracho
EFFECT OF NOZZLE CONFIGURATION ON MACROSCOPIC SPRAY CHARACTERISTICS OF MULTI-HOLE FUEL INJECTORS UNDER SUPERHEATED CONDITIONS
Atomization and Sprays, Vol.26, 2016, issue 5
Gele Aori, Ming Zhang, David L. S. Hung, Tianyun Li, Gaomimg Zhang
A NUMERICAL METHOD FOR ANALYSIS OF SPRAY BEHAVIOR WITH DESIGN OF EXPERIMENT
Atomization and Sprays, Vol.24, 2014, issue 11
Hyungsoo Ha, Jeongkuk Yeom
Image Analysis of a Diesel Spray Impinging on a Wall
International Journal of Fluid Mechanics Research, Vol.24, 1997, issue 1-3
Masataka Arai, T. Ebara, Kenji Amagai
EXPERIMENTAL AND NUMERICAL STUDY OF INTERNAL FLOW AND SPRAY CHARACTERISTICS FOR ELLIPTICAL ORIFICE UNDER TYPICAL DIESEL ENGINE OPERATION CONDITIONS
Atomization and Sprays, Vol.28, 2018, issue 8
Bifeng Yin, Bin Xu, Shenghao Yu, Ze Ye, Huaping Xu, Hekun Jia, Weixin Deng