Abo Bibliothek: Guest
Digitales Portal Digitale Bibliothek eBooks Zeitschriften Referenzen und Berichte Forschungssammlungen
Atomization and Sprays
Impact-faktor: 1.737 5-jähriger Impact-Faktor: 1.518 SJR: 0.814 SNIP: 1.18 CiteScore™: 2.2

ISSN Druckformat: 1044-5110
ISSN Online: 1936-2684

Volumes:
Volumen 30, 2020 Volumen 29, 2019 Volumen 28, 2018 Volumen 27, 2017 Volumen 26, 2016 Volumen 25, 2015 Volumen 24, 2014 Volumen 23, 2013 Volumen 22, 2012 Volumen 21, 2011 Volumen 20, 2010 Volumen 19, 2009 Volumen 18, 2008 Volumen 17, 2007 Volumen 16, 2006 Volumen 15, 2005 Volumen 14, 2004 Volumen 13, 2003 Volumen 12, 2002 Volumen 11, 2001 Volumen 10, 2000 Volumen 9, 1999 Volumen 8, 1998 Volumen 7, 1997 Volumen 6, 1996 Volumen 5, 1995 Volumen 4, 1994 Volumen 3, 1993 Volumen 2, 1992 Volumen 1, 1991

Atomization and Sprays

DOI: 10.1615/AtomizSpr.v17.i8.10
pages 659-681

CHARACTERISTICS OF WATER DROPLET IMPACTION BEHAVIOR ON A POLISHED STEEL HEATED SURFACE: PART I

S. W. Akhtar
Institute for Nuclear Power, P.O. Box 3140, Islamabad, Pakistan
Ghasem G. Nasr
Spray Research Group (SRG), Insititute of Materials Research (IMR), School of Computing, Science and Engineering, University of Salford, Manchester, UK
Andrew J. Yule
Spray Research Group (SRG), Insititute of Materials Research (IMR), School of Computing, Science and Engineering, University of Salford, Manchester, UK; Thermofluids Division, Department of Mechanical Engineering, UMIST

ABSTRAKT

This paper, which is in two parts, presents the results and analysis of droplet impaction on a hot stainless steel surface. Part I of this study reports the results of analysis of high-speed visualizations of droplet impaction phenomena on a hot stainless steel surface, including the characteristics of reatomized droplets that are produced at high impact Weber numbers. The investigation extends to ranges of smaller droplets and higher velocities compared with published research. Part II will then provide the results and analysis of the droplet impaction heat transfer on a hot surface. The 3.0 mm diameter flat stainless steel surface was heated to temperatures of 140°C < Tw < 400°C, and water sprays were produced from a droplet generation system based on an 80 mm diameter rotary cup. Droplet sizes in the range 20 μm < D < 160 μm were used, impacting with velocities of 5 ms−1 < U < 18 ms−1 . Previous research relevant to the topic is reviewed. Physical models for different forms of droplet breakup in different regimes are developed from the new experiments and compared with existing models. Data are presented for the droplet spreading characteristics, as well as reatomized droplet characteristics, under relatively high impact Weber number conditions (i.e., 100 < We < 750), and for different boiling regimes. These data are correlated well using equations that can be justified by physical arguments.


Articles with similar content:

CHARACTERISTICS OF WATER DROPLET IMPACTION BEHAVIOR ON A POLISHED STEEL HEATED SURFACE: Part II
Atomization and Sprays, Vol.17, 2007, issue 8
Ghasem G. Nasr, Andrew J. Yule, S. W. Akhtar
HEAT TRABSFER FOR SINGLE AND MULTIPLE DROPLET IMPINGEMENT ON WALLS
ICLASS 94
Proceedings of the Sixth International Conference on Liquid Atomization and Spray Systems, Vol.0, 1994, issue
Marwan Al-Roub, Patrick V. Farrell, Jeffrey Naber
CHARACTERIZATION OF TRAJECTORY, BREAK POINT, AND BREAK POINT DYNAMICS OF A PLAIN LIQUID JET IN A CROSSFLOW
Atomization and Sprays, Vol.21, 2011, issue 3
U. M. Mondragon, Q. Wang, C. T. Brown, Vincent G. McDonell
ANALYSIS OF PRESSURE SWIRL AND PURE AIRBLAST ATOMIZATION
Atomization and Sprays, Vol.1, 1991, issue 2
A. J. Przekwas, Chien-Pei Mao, S. G. Chuech
EXPERIMENTAL INVESTIGATION OF JET BREAKUP AT LOW WEBER NUMBER
Atomization and Sprays, Vol.27, 2017, issue 9
Raj M. Manglik, S. Rajendran, Milind A. Jog