Abo Bibliothek: Guest
Digitales Portal Digitale Bibliothek eBooks Zeitschriften Referenzen und Berichte Forschungssammlungen
Atomization and Sprays
Impact-faktor: 1.262 5-jähriger Impact-Faktor: 1.518 SJR: 0.814 SNIP: 1.18 CiteScore™: 1.6

ISSN Druckformat: 1044-5110
ISSN Online: 1936-2684

Volumes:
Volumen 29, 2019 Volumen 28, 2018 Volumen 27, 2017 Volumen 26, 2016 Volumen 25, 2015 Volumen 24, 2014 Volumen 23, 2013 Volumen 22, 2012 Volumen 21, 2011 Volumen 20, 2010 Volumen 19, 2009 Volumen 18, 2008 Volumen 17, 2007 Volumen 16, 2006 Volumen 15, 2005 Volumen 14, 2004 Volumen 13, 2003 Volumen 12, 2002 Volumen 11, 2001 Volumen 10, 2000 Volumen 9, 1999 Volumen 8, 1998 Volumen 7, 1997 Volumen 6, 1996 Volumen 5, 1995 Volumen 4, 1994 Volumen 3, 1993 Volumen 2, 1992 Volumen 1, 1991

Atomization and Sprays

DOI: 10.1615/AtomizSpr.2015011000
pages 587-615

DEVELOPMENT OF AN IMPROVED SPRAY/WALL INTERACTION MODEL FOR DIESEL-LIKE SPRAY IMPINGEMENT SIMULATIONS

Peng Deng
State Key Laboratory of Advanced Design and Manufacturing for Vehicle Body, Hunan University, Changsha, China; Engine Research Center, University of Wisconsin-Madison, Rm 1018A, 1500 Engineering Drive, Madison, Wisconsin 53706, USA
Qi Jiao
Engine Research Center, University of Wisconsin-Madison, Rm 1018A, 1500 Engineering Drive, Madison, Wisconsin 53706, USA
Rolf D. Reitz
Engine Research Center, University of Wisconsin-Madison, Rm 1018A, 1500 Engineering Drive, Madison, Wisconsin 53706, USA
Zhiyu Han
State Key Laboratory of Advanced Design and Manufacturing for Vehicle Body, Hunan University, Changsha, China; Huai'an Industrial Technology Research Institute, Huai'an, China

ABSTRAKT

A new spray/wall interaction model was developed with emphasis on the simulation of diesel-like spray impingement generated by high injection pressures, which is widely used in direct-injection gasoline and diesel engines. In contrast to traditional spray/wall interaction models, lift forces were considered on the wall spray droplets in the new model, which generates a vortex at the leading edge of the wall spray instead of droplet rebound or splash. In addition, a wall-jet submodel was adopted to correct the droplet-gas relative velocity in the calculation of drag and lift forces on the droplets. Grid dependency was also significantly reduced in the new model due to the implementation of the wall-jet submodel. The wall-jet submodel was extended to cover both normal and oblique impingements, which are relevant in engines with a side-mounted injector. In the new model a new correlation was also developed to estimate the splashed mass ratio for each individual impact droplet, which provides a more accurate prediction of the overall spray impingement process. Extensive validations of the new model were performed through comparisons against measurements from a variety of diesel spray impingement experiments, instead of just using single drop or drop train impingement experiments. The results indicate that the new model matches experimental measurements very well and can be used for the prediction of spray/wall interaction, especially under the conditions relevant to modern direct-injection diesel and gasoline engines.


Articles with similar content:

A UNIFIED FUEL SPRAY BREAKUP MODEL FOR INTERNAL COMBUSTION ENGINE APPLICATIONS
Atomization and Sprays, Vol.18, 2008, issue 5
Dennis N. Assanis, Christos Chryssakis
LINKING NOZZLE FLOW WITH SPRAY CHARACTERISTICS IN A DIESEL FUEL INJECTION SYSTEM
Atomization and Sprays, Vol.8, 1998, issue 3
Manolis Gavaises, C. Arcoumanis
SPRAY AND COMBUSTION MODELING IN GASOLINE DIRECT-INJECTION ENGINES
Atomization and Sprays, Vol.10, 2000, issue 3-5
Rolf D. Reitz, Li Fan
EXPERIMENTAL INVESTIGATION OF SPRAY CHARACTERISTICS OF DIESEL-METHANOL-WATER EMULSION
Atomization and Sprays, Vol.25, 2015, issue 8
Wuqiang Wang, Shenteng Cao, Dongyin Wu, Junjie Yan, Zhenzhou Pang
CHARACTERIZATION OF HIGH-INJECTION-PRESSURE DIESEL SPRAYS WITH RELATION TO PARTICULATE AND NOx EMISSIONS
Atomization and Sprays, Vol.8, 1998, issue 1
T. F. Su, Patrick V. Farrell