Abo Bibliothek: Guest
Digitales Portal Digitale Bibliothek eBooks Zeitschriften Referenzen und Berichte Forschungssammlungen
Atomization and Sprays
Impact-faktor: 1.737 5-jähriger Impact-Faktor: 1.518 SJR: 0.814 SNIP: 1.18 CiteScore™: 2.2

ISSN Druckformat: 1044-5110
ISSN Online: 1936-2684

Volumes:
Volumen 30, 2020 Volumen 29, 2019 Volumen 28, 2018 Volumen 27, 2017 Volumen 26, 2016 Volumen 25, 2015 Volumen 24, 2014 Volumen 23, 2013 Volumen 22, 2012 Volumen 21, 2011 Volumen 20, 2010 Volumen 19, 2009 Volumen 18, 2008 Volumen 17, 2007 Volumen 16, 2006 Volumen 15, 2005 Volumen 14, 2004 Volumen 13, 2003 Volumen 12, 2002 Volumen 11, 2001 Volumen 10, 2000 Volumen 9, 1999 Volumen 8, 1998 Volumen 7, 1997 Volumen 6, 1996 Volumen 5, 1995 Volumen 4, 1994 Volumen 3, 1993 Volumen 2, 1992 Volumen 1, 1991

Atomization and Sprays

DOI: 10.1615/AtomizSpr.v8.i3.20
pages 255-266

SPRAY FORMATION BY FLASHING OF A BINARY MIXTURE: A PARAMETRIC STUDY

Michal Zeigerson-Katz
The Pearlstone Center for Aeronautical Studies, Department of Mechanical Engineering, Ben-Gurion University of the Negev, Beer-Sheva, Israel
Eran Sher
Professor Emeritus, Technion - Israel Institute of Technology

ABSTRAKT

A binary liquid mixture which consists of a low-vapor-pressure liquid and a propellant has been considered. When the mixture is discharged through an appropriate injection system, the propellant undergoes a rapid flash boiling process which results in a disintegration of the continuous liquid phase into small droplets. In the present work, the effect of the injection system design on the spray characteristics is investigated experimentally. It is concluded that: (1) the real behavior of the solution, as compared to ideal solution behavior, is an important factor; (2) the important stage of nucleation occurs at the metering orifice and apparently, the main duct does not play any significant role in the bubbles' nucleation; (3) neither the expansion chamber diameter nor its length has any significant effect on the droplet Sauter mean diameter (SMD), (4) an orifice's diameters ratio (metering to discharge) between 0.6 and 0.9 results in a minimum SMD; and (5) the SMD is correlated well with a modified version of the Jakob number of the form of Ja* = xβ(CpΔT/hfg).


Articles with similar content:

EXAMINATION OF NEAR-WALL SCALING FOR TURBULENT BOUNDARY LAYERS WITH ADVERSE PRESSURE GRADIENT
TSFP DIGITAL LIBRARY ONLINE, Vol.5, 2007, issue
Margareta Petrovan Boiarciuc, Nikolaus Peller, Christophe Brun, Michael Manhart
EFFERVESCENT ATOMIZATION OF GASOLINE CONTAINING DISSOLVED CO2
Atomization and Sprays, Vol.14, 2004, issue 4
A. Rashkovan, V. Kholmer, Eran Sher
CHARACTERISTICS OF TRANSIENT, SWIRL-GENERATED, HOLLOW-CONE SPRAYS
Atomization and Sprays, Vol.16, 2006, issue 5
Julian T. Kashdan, John S. Shrimpton
EFFECT OF INJECTION PRESSURE ON SPRAY CHARACTERISTICS AND FUEL DISTRIBUTION IN DIESEL ENGINE CONDITIONS BY PLANAR LASER-INDUCED EXCIPLEX FLUORESCENCE (PLIEF) TECHNOLOGY
Atomization and Sprays, Vol.18, 2008, issue 8
Hongsong Guo, Wanhua Su, Tian Sun
THE STOCHASTIC LAGRANGIAN MODEL OF DROP BREAKUP IN THE COMPUTATION OF LIQUID SPRAYS
Atomization and Sprays, Vol.11, 2001, issue 5
Mikhael Gorokhovski