Abo Bibliothek: Guest
Digitales Portal Digitale Bibliothek eBooks Zeitschriften Referenzen und Berichte Forschungssammlungen
Atomization and Sprays
Impact-faktor: 1.737 5-jähriger Impact-Faktor: 1.518 SJR: 0.814 SNIP: 1.18 CiteScore™: 2.2

ISSN Druckformat: 1044-5110
ISSN Online: 1936-2684

Volumes:
Volumen 30, 2020 Volumen 29, 2019 Volumen 28, 2018 Volumen 27, 2017 Volumen 26, 2016 Volumen 25, 2015 Volumen 24, 2014 Volumen 23, 2013 Volumen 22, 2012 Volumen 21, 2011 Volumen 20, 2010 Volumen 19, 2009 Volumen 18, 2008 Volumen 17, 2007 Volumen 16, 2006 Volumen 15, 2005 Volumen 14, 2004 Volumen 13, 2003 Volumen 12, 2002 Volumen 11, 2001 Volumen 10, 2000 Volumen 9, 1999 Volumen 8, 1998 Volumen 7, 1997 Volumen 6, 1996 Volumen 5, 1995 Volumen 4, 1994 Volumen 3, 1993 Volumen 2, 1992 Volumen 1, 1991

Atomization and Sprays

DOI: 10.1615/AtomizSpr.2012005918
pages 581-601

VACUUM-ASSISTED GAS ATOMIZATION OF LIQUID METAL

Steven P. Mates
National Institute of Standards and Technology, Gaithersburg, MD, 20899, USA
S. D. Ridder
National Institute of Standards and Technology, Gaithersburg, MD, 20899, USA
F. S. Biancaniello
National Institute of Standards and Technology, Gaithersburg, MD, 20899, USA
T. Zahrah
MATSYS, Inc., Sterling, VA, 20166, USA

ABSTRAKT

Vacuum-assisted gas atomization of liquid metal is explored. The investigation is motivated by observations of liquid metal atomization that indicate that secondary atomization is sustained over an extended distance from the nozzle tip. Increasing the velocity of the gas flow downstream of the nozzle exit by lowering the nozzle back pressure below ambient may therefore improve atomization efficiency. Supersonic jets grow in length when the nozzle back pressure is lowered due to an increase in the nozzle pressure ratio. However, since the nozzle mass flux remains fixed, any improvements in vacuum-assisted atomization efficiency will be realized without any increase to the gas-to-metal mass flow ratio, which is of interest both academically and practically as gas consumption can be costly. Small (25-kg batch) atomization runs were performed using an Al-Cu-Ni glass-forming alloy in which a high-mass-flow vacuum system was employed to maintain a sub-ambient chamber pressure over the course of an entire run. The powder produced in this manner was then compared to the conventional method without the vacuum system operating. Results demonstrate that atomizing into a partial vacuum decreases the frequency of the coarsest particles in the powder size distributions, leading to a narrower particle size distribution. Further, they underscore the importance of the axial length scale affecting secondary atomization that is related to, but not fully described by, the gas-to-liquid mass flux ratio. The present experiments point out a significant and unexplored parameter space that may be exploited to increase control over particle size distributions.


Articles with similar content:

SPRAY EVOLUTION IN A TWIN-FLUID SWIRL ATOMIZER
Atomization and Sprays, Vol.18, 2008, issue 5
J. Karnawat, Abhijit Kushari
EFFECT OF LINEAR ALKANE C17, C18 ON SPRAY CHARACTERISTICS OF KEROSENE IN HOLLOW CONE PRESSURE SWIRL SPRAY
Atomization and Sprays, Vol.27, 2017, issue 6
Haitao Ren, Xiaoyi Yang, Zhiwen Gan
EXPERIMENTAL INVESTIGATION ON NEAR-FIELD BREAKUP CHARACTERISTICS OF HYBRID-MIXED TWIN-FLUID ATOMIZER
Atomization and Sprays, Vol.28, 2018, issue 10
T. Y. Li, Shiyan Li, X. Y. Yang, Yi Gao, C. Fu
AIR-ASSIST PRESSURE-SWIRL ATOMIZATION
Atomization and Sprays, Vol.9, 1999, issue 2
Paul E. Sojka, U. T. Schmidt
ATOMIZATION OF GELLED PROPELLANTS FROM SWIRL INJECTORS WITH LEAF SPRING IN SWIRL CHAMBER
Atomization and Sprays, Vol.21, 2011, issue 11
Ming-Xi Tong, Wei Zhang, Qing-Fei Fu, Li-Jun Yang, Ming-long Du