Abo Bibliothek: Guest
Digitales Portal Digitale Bibliothek eBooks Zeitschriften Referenzen und Berichte Forschungssammlungen
Atomization and Sprays
Impact-faktor: 1.262 5-jähriger Impact-Faktor: 1.518 SJR: 0.814 SNIP: 1.18 CiteScore™: 1.6

ISSN Druckformat: 1044-5110
ISSN Online: 1936-2684

Volumes:
Volumen 29, 2019 Volumen 28, 2018 Volumen 27, 2017 Volumen 26, 2016 Volumen 25, 2015 Volumen 24, 2014 Volumen 23, 2013 Volumen 22, 2012 Volumen 21, 2011 Volumen 20, 2010 Volumen 19, 2009 Volumen 18, 2008 Volumen 17, 2007 Volumen 16, 2006 Volumen 15, 2005 Volumen 14, 2004 Volumen 13, 2003 Volumen 12, 2002 Volumen 11, 2001 Volumen 10, 2000 Volumen 9, 1999 Volumen 8, 1998 Volumen 7, 1997 Volumen 6, 1996 Volumen 5, 1995 Volumen 4, 1994 Volumen 3, 1993 Volumen 2, 1992 Volumen 1, 1991

Atomization and Sprays

DOI: 10.1615/AtomizSpr.2014011025
pages 1089-1135

A STUDY OF DROPLET COLLISION MODELLING FOR SPRAY FORMATION AND MIXING WITH A TWO-ROW GROUP-HOLE INJECTION NOZZLE FOR DIESEL ENGINES

Pavlos Aleiferis
Department of Mechanical Engineering, Imperial College London, London SW7 2AZ, United Kingdom
M. Ashrafi-Nik
Department of Mechanical Engineering, University College, Torrington Place, London WC1E 7JE, London, UK
N. Ladommatos
Department of Mechanical Engineering, University College, Torrington Place, London WC1E 7JE, London, UK
G. Dober
Delphi Automotive Systems, Avenue De Luxembourg, L-4940 Bascharage (Nidderkaerjeng), Luxembourg
Kourosh Karimi
Delphi Automotive Systems, Avenue De Luxembourg, L-4940 Bascharage (Nidderkaerjeng), Luxembourg

ABSTRAKT

Improvement of the diesel engine and optimization of the combustion process continues to be an important aspect of efforts to meet new emissions regulations. The most important factors which directly influence the performance of a diesel engine are related to the spray formation and vaporization of the liquid fuel upon injection into the cylinder. Therefore in order to improve diesel engines, new studies need to be undertaken to further develop the injection system and, in particular, the nozzle layout and subsequent spray formation. This paper describes the computational modelling process of spray formation and atomization from a novel type of diesel injector with a nozzle layout that consists of a group of upper and lower sets of holes. A version of the KIVA-3V open-source code with extended capability of large eddy simulation (LES) was utilized for this work. Particular attention was paid to modelling droplet collision processes as the two rows of sprays were at converging angles to each other, promoting spray interactions. The simulated results were compared against experimental data in terms of spray penetration length and curvature for the vapor and liquid phases of the fuel. The experiments were conducted in an optical compression machine using high-speed schlieren and Mie scattering imaging techniques. Significant improvement in the simulation process and better agreement with experimental data was observed when additional modes of droplet collisions were coded, namely, reflexive and stretching separation. The methodology was also tested with different injection pressures of 1200 and 1800 bar. The use of additional modes of droplet collisions was also found beneficial for a typical single-row injector whose results were compared against the two-row injector and benchmarking experiments under the same conditions.


Articles with similar content:

MODELLING OF PRIMARY BREAKUP PROCESS OF A GASOLINE DIRECT ENGINE MULTI-HOLE SPRAY
Atomization and Sprays, Vol.23, 2013, issue 10
Giuseppe Cantore, Simone Malaguti, Luigi Allocca, Alessandro Montanaro, Stefano Fontanesi
LINKING NOZZLE FLOW WITH SPRAY CHARACTERISTICS IN A DIESEL FUEL INJECTION SYSTEM
Atomization and Sprays, Vol.8, 1998, issue 3
Manolis Gavaises, C. Arcoumanis
FLASH-BOILING INITIALIZATION FOR SPRAY SIMULATIONS BASED ON PARAMETRIC STUDIES
Atomization and Sprays, Vol.28, 2018, issue 2
Sampath K. Rachakonda, David P. Schmidt, Yue Wang
GASOLINE DIRECT INJECTION SPRAY SIMULATION
ICHMT DIGITAL LIBRARY ONLINE, Vol.11, 2004, issue
Gino Bella, Rossella Rotondi
SPRAY AND COMBUSTION MODELING IN GASOLINE DIRECT-INJECTION ENGINES
Atomization and Sprays, Vol.10, 2000, issue 3-5
Rolf D. Reitz, Li Fan