Abo Bibliothek: Guest
Digitales Portal Digitale Bibliothek eBooks Zeitschriften Referenzen und Berichte Forschungssammlungen
Atomization and Sprays
Impact-faktor: 1.737 5-jähriger Impact-Faktor: 1.518 SJR: 0.814 SNIP: 1.18 CiteScore™: 2.2

ISSN Druckformat: 1044-5110
ISSN Online: 1936-2684

Volumes:
Volumen 30, 2020 Volumen 29, 2019 Volumen 28, 2018 Volumen 27, 2017 Volumen 26, 2016 Volumen 25, 2015 Volumen 24, 2014 Volumen 23, 2013 Volumen 22, 2012 Volumen 21, 2011 Volumen 20, 2010 Volumen 19, 2009 Volumen 18, 2008 Volumen 17, 2007 Volumen 16, 2006 Volumen 15, 2005 Volumen 14, 2004 Volumen 13, 2003 Volumen 12, 2002 Volumen 11, 2001 Volumen 10, 2000 Volumen 9, 1999 Volumen 8, 1998 Volumen 7, 1997 Volumen 6, 1996 Volumen 5, 1995 Volumen 4, 1994 Volumen 3, 1993 Volumen 2, 1992 Volumen 1, 1991

Atomization and Sprays

DOI: 10.1615/AtomizSpr.2013008918
pages 273-280

PREDICTION OF PRESSURE DROP THROUGH BAFFLE INJECTOR

Kyubok Ahn
School of Mechanical Engineering, Chungbuk National University, Chungbuk, Korea
Hwan-Seok Choi
Combustion Chamber Department, Korea Aerospace Research Institute, Daejeon, Korea

ABSTRAKT

The baffle injector in a liquid rocket engine has two special objectives. One is to atomize effectively propellants and the other is to prevent combustion instabilities. A novel analytical method predicting a fuel-side pressure drop through a baffle injector has been suggested. In order to prove the accuracy of the proposed analytical method, three baffle injector models with different hole diameters and cooling channels were manufactured. At the same pressure drop, cold-flow tests using tap water have been carried out for measuring mass flow rates and calculating discharge coefficients. The discharge coefficients measured by the cold-flow tests have been compared with those calculated by the proposed analytical method. It is found that the analytical method can estimate the discharge coefficients within 1% error.


Articles with similar content:

A STUDY ON DISCHARGE COEFFICIENTS OF CLOSED-TYPE SWIRL INJECTORS FOR A LIQUID ROCKET ENGINE
Atomization and Sprays, Vol.27, 2017, issue 7
Kyubok Ahn, Hwan-Seok Choi
FLOW CHARACTERISTICS OF CLOSE-TYPE SWIRL INJECTORS MANUFACTURED BY A 3D PRINTER
Atomization and Sprays, Vol.27, 2017, issue 2
Wonjae Yoon , Kyubok Ahn
EXPERIMENTAL AND COMPUTATIONAL STUDY OF THE INFLUENCE OF PARTIAL NEEDLE LIFT ON NOZZLE FLOWIN DIESEL FUEL INJECTORS
Atomization and Sprays, Vol.22, 2012, issue 8
Jaime Gimeno, Raul Payri, Alejandro H. Plazas, O. Venegas
TWO PARAMETRIC FLOW MEASUREMENT IN GAS-LIQUID TWO-PHASE FLOW
International Heat Transfer Conference 7, Vol.10, 1982, issue
Xu Yinlong , Chen Zhihang, Chen Zuyao, Zhao Zaisan
Precision Setup for Fluid Pump Efficiency Testing
Heat Transfer Research, Vol.28, 1997, issue 7-8
Yu. D. Zozulyak, Yu. L. Levashov, V. T. Novatsky