Abo Bibliothek: Guest
Digitales Portal Digitale Bibliothek eBooks Zeitschriften Referenzen und Berichte Forschungssammlungen
International Journal of Fluid Mechanics Research
ESCI SJR: 0.206 SNIP: 0.446 CiteScore™: 0.9

ISSN Druckformat: 2152-5102
ISSN Online: 2152-5110

Volumes:
Volumen 47, 2020 Volumen 46, 2019 Volumen 45, 2018 Volumen 44, 2017 Volumen 43, 2016 Volumen 42, 2015 Volumen 41, 2014 Volumen 40, 2013 Volumen 39, 2012 Volumen 38, 2011 Volumen 37, 2010 Volumen 36, 2009 Volumen 35, 2008 Volumen 34, 2007 Volumen 33, 2006 Volumen 32, 2005 Volumen 31, 2004 Volumen 30, 2003 Volumen 29, 2002 Volumen 28, 2001 Volumen 27, 2000 Volumen 26, 1999 Volumen 25, 1998 Volumen 24, 1997 Volumen 23, 1996 Volumen 22, 1995

International Journal of Fluid Mechanics Research

DOI: 10.1615/InterJFluidMechRes.2018024538
pages 63-87

ANALYSIS OF THE EXCHANGE PROCESS IN ICE USING A MOVING MESH APPROACH

Mustapha Bordjane
Laboratoire de Mécanique Appliquée (LMA), Université des Sciences et de la Technologie Mohamed Boudiaf d'Oran, B.P. 1505, El Mnaouer, 31000 Oran-Algérie
David Chalet
LHEEA Lab (ECN/CNRS), Ecole Centrale de Nantes, 44300 Nantes, France

ABSTRAKT

Fluid flow characteristics in internal combustion engines have been studied for a long time by experimental approaches. But today, computational fluid dynamics (CFD) simulations have become a useful tool, especially with new, more powerful computers. On another side, experimental tests have become highly onerous and overpriced. In addition, investigations using this kind of methodology are limited to small parts of the system. Thus, an alternative solution to carry out this study is CFD simulation and modeling. The latter is more economical in time and cost. The aim of this article is to explore the flow characteristics during the exchange process, which has a crucial influence on the performance of the internal combustion engine and on pollutant emissions and noise. In this study, two different approaches related to the modeling of engines are tested: CFD simulations using a moving mesh strategy and a zero-dimensional model, the so-called inertial capacitive model. For the first approach, a dynamic mesh model was used to simulate piston, intake, and exhaust valve motion during the open phase of a nonignited single-cylinder four-stroke-cycle engine. The second approach used in this study was retained to the formulation and application of the new (0D) inertial capacitive model based on the first thermodynamic principle, Newton's second law, and the associated laws of fluid mechanics relative to gas dynamics in the intake and exhaust manifolds of internal combustion engines. The subject of the second approach is to check the validity of the CFD analysis and to calibrate some parameters deduced from the tuning process of the problem considered.


Articles with similar content:

ESTIMATE OF THE SUBGRID VARIANCE OF THE MIXTURE FRACTION IN SPRAY TURBULENT COMBUSTION
ICHMT DIGITAL LIBRARY ONLINE, Vol.13, 2008, issue
Hicham Meftah, Zakaria Bouali, Francois-Xavier Demoulin, Ahmed Mir, Julien Reveillon
NUMERICAL AND EXPERIMENTAL APPROACH FOR COOLING SYSTEM OPTIMIZATION IN AN AIR-COOLED CNG ENGINE
Proceedings of the 24th National and 2nd International ISHMT-ASTFE Heat and Mass Transfer Conference (IHMTC-2017), Vol.0, 2017, issue
Prafulla P. Ghare, Amit Chaudhari, Alok Deshpande, Ashish Sontakke
Recent developments in turbulent combustion modeling: automated progress variables definition − Ignition combustion regimes after rapid compression
ICHMT DIGITAL LIBRARY ONLINE, Vol.0, 2012, issue
Guillaume Lodier , Y.-S. Niu, Pascale Domingo, Luc Vervisch
GAS/DIESEL DUAL-FUEL COMBUSTION MODELLING FOR ENGINE CONDITIONS
ICHMT DIGITAL LIBRARY ONLINE, Vol.4, 2001, issue
R. T. Casey, Brian E. Milton, Hayan Miao
Numerical Predictions of High-Speed Rotating Labyrinth Seal Performance: Influence of Rotation on Power Dissipation and Temperature Rise
ICHMT DIGITAL LIBRARY ONLINE, Vol.0, 1992, issue
Th. Scherer, W. Waschka, Sigmar Wittig