Suscripción a Biblioteca: Guest
Portal Digitalde Biblioteca Digital eLibros Revistas Referencias y Libros de Ponencias Colecciones
Journal of Enhanced Heat Transfer
Factor de Impacto: 1.406 Factor de Impacto de 5 años: 1.075 SJR: 0.287 SNIP: 0.653 CiteScore™: 1.2

ISSN Imprimir: 1065-5131
ISSN En Línea: 1563-5074

Volumes:
Volumen 27, 2020 Volumen 26, 2019 Volumen 25, 2018 Volumen 24, 2017 Volumen 23, 2016 Volumen 22, 2015 Volumen 21, 2014 Volumen 20, 2013 Volumen 19, 2012 Volumen 18, 2011 Volumen 17, 2010 Volumen 16, 2009 Volumen 15, 2008 Volumen 14, 2007 Volumen 13, 2006 Volumen 12, 2005 Volumen 11, 2004 Volumen 10, 2003 Volumen 9, 2002 Volumen 8, 2001 Volumen 7, 2000 Volumen 6, 1999 Volumen 5, 1998 Volumen 4, 1997 Volumen 3, 1996 Volumen 2, 1995 Volumen 1, 1994

Journal of Enhanced Heat Transfer

DOI: 10.1615/JEnhHeatTransf.v6.i2-4.80
pages 151-160

Effects of Size and Number Density of Micro-reentrant Cavities on Boiling Heat Transfer from a Silicon Chip Immersed in Degassed and Gas-dissolved FC-72

H. Kubo
Interdisciplinary Graduate School of Engineering Sciences, Kyushu University, Kasuga, Fukuoka 816-8580, Japan
Hiroshi Takamatsu
Department of Mechanical Engineering, Kyushu University, Fukuoka 819-0395, Japan
Hiroshi Honda
Institute of Advanced Material Study, Kyushu University, Kasuga, Fukuoka 816-8580, Japan

SINOPSIS

Boiling heat transfer of FC-72 from newly developed treated surfaces with micro-reentrant cavities was studied experimentally. The surface structure was fabricated on a silicon chip by use of microelectronic fabrication techniques. Four kinds of treated surfaces with the combinations of two cavity mouth diameters (about 1.6 μm and 3.1 μm) and two number densities of the micro-reentrant cavities (81 l/cm2 and 96 × 103 l/cm2) were tested along with a smooth surface. Experiments were conducted at the liquid subcoolings of 3 K and 25 K with degassed and gas-dissolved FC-72. While the wall superheat at boiling incipience was strongly dependent on the dissolved gas content; it was little affected by the cavity mouth diameter and the liquid subcooling. The heat transfer performance of the treated surface was considerably higher than that of the smooth surface. The highest performance was obtained with a treated surface with a larger cavity mouth diameter and a larger cavity number density. The results were compared with those for previously developed treated surfaces.


Articles with similar content:

BOILING HEAT TRANSFER FROM A SILICON CHIP IMMERSED IN DEGASSED AND GAS-DISSOLVED FC-72: EFFECTED BY SIZE AND NUMBER DENSITY OF MICRO-REENTRANT CAVITIES
Journal of Enhanced Heat Transfer, Vol.24, 2017, issue 1-6
Hiroshi Takamatsu, Hiroshi Honda, H. Kubo
Enhanced Boiling Heat Transfer from Silicon Chips with Micro-Pin Fins Immersed in FC-72
Journal of Enhanced Heat Transfer, Vol.10, 2003, issue 2
Hiroshi Takamatsu, Hiroshi Honda, Jin Jia Wei
EFFECT OF SUBCOOLING ON POOL BOILING HEAT TRANSFER IN WATER USING SINTERED COPPER MICROPOROUS COATING
Second Thermal and Fluids Engineering Conference, Vol.3, 2017, issue
Seongchul Jun, Hwan Yeol Kim, Jinsub Kim, Seung-Moon You
Effect of the size of micro-pin-fin on boiling heat transfer from silicon chips immersed in FC-72
International Heat Transfer Conference 12, Vol.46, 2002, issue
Hiroshi Takamatsu, Hiroshi Honda, Jin Jia Wei
Enhanced pool boiling CHF in FC-72 from modulated porous layer coating
ICHMT DIGITAL LIBRARY ONLINE, Vol.2, 2004, issue
Klemen Ferjancic, D. Rajselj, Iztok Golobic