Suscripción a Biblioteca: Guest
Portal Digitalde Biblioteca Digital eLibros Revistas Referencias y Libros de Ponencias Colecciones
High Temperature Material Processes: An International Quarterly of High-Technology Plasma Processes
SJR: 0.176 SNIP: 0.48 CiteScore™: 1.3

ISSN Imprimir: 1093-3611
ISSN En Línea: 1940-4360

High Temperature Material Processes: An International Quarterly of High-Technology Plasma Processes

DOI: 10.1615/HighTempMatProc.v2.i3.40
pages 339-357

RESIDUAL STRESS MEASUREMENT DURING PLASMA SPRAYING OF ALUMINA OR ZIRCONIA AND COMPARISON WITH A ID MODEL

A.C. Leger
University of Limoges - L.M.C.T.S. ESA 6015 - 123, Avenue Albert Thomas 87060 LIMOGES Cedex - France
Guy Delluc
Laboratoire Sciences des Precedes Ceramiques et Traitements de Surfaces UMR CNRS 6638, 123 avenue Albert Thomas 87060 Limoges Cedex
A. Haddadi
Laboratoire de Materiaux Ceramiques et Traitements de Surface - ESA CNRS 6015 Universite de Limoges - 123, Avenue Albert Thomas 87060 Limoges Cedex - France
Pierre Fauchais
Laboratoire Sciences des Procedes Ceramiques et de Traitements de Surface UMR CNRS 6638 University of Limoges 123 avenue Albert Thomas, 87060 LIMOGES - France
F. Nardou
Laboratoire de Materiaux Ceramiques et Traitements de Surface - ESA CNRS 6015 Universite de Limoges - 123, Avenue Albert Thomas 87060 Limoges Cedex - France

SINOPSIS

A system, developed in the laboratory, allows to record in situ the deformation of a flat beam with a displacement sensor and so to analyse stresses formation during spraying and upon cooling with fixed or rotating substrates.
For alumina coatings sprayed on XC38 forged steel substrates a systematic study of the preheating temperature and pass thickness has been performed. Preheating temperature was varied from 200°C to 700°C and pass thicknesses were either thin (3 to 25 µm) or thick (60 to 180 µm). In the latter case the splats within a pass remain in a molten state as soon as the deposited thickness is over 100-180 µm depending on spraying conditions.
For thin passes the quenching stress σq increases with temperature and is maximum for 25 µm thick passes (up to 70 MPa at 600°C). For thick passes preheating temperature must be lower than 500°C and σq reaches a maximum of 55 MPa. The corresponding coating cross sections show the existence of macrocracks. The comparison of the experimental results with those calculated with a ID simplified model developed by Tsui and Clyne allows to determine, the Young's modulus Ed of the coatings. For thin passes Ed can reach 160 GPa while for thick passes it reaches its peak at about 70 GPa.


Articles with similar content:

PLASMA SPRAYED COATINGS OF MECHANOFUSED ALUMINA-STEEL PARTICLES
Progress in Plasma Processing of Materials, 1999, Vol.1, 1999, issue
Helene Ageorges, Alain Grimaud, Pierre Fauchais
PLASMA SPRAYED COATINGS OF MECHANOFUSED ALUMINA-STEEL PARTICLES
High Temperature Material Processes: An International Quarterly of High-Technology Plasma Processes, Vol.14, 2010, issue 4
Helene Ageorges, Alain Grimaud, Pierre Fauchais
MECHANICAL PROPERTIES OF STEEL-COPPER POLYMETAL MANUFACTURED BY THE WIRE-FEED ELECTRON-BEAM ADDITIVE TECHNOLOGY
High Temperature Material Processes: An International Quarterly of High-Technology Plasma Processes, Vol.24, 2020, issue 2
Evgeny A. Kolubaev, Kseniya S. Osipovich, A. V. Gusarova, Andrey V. Chumaevskii, K. N. Kalashnikov
DEVELOPMENT OF EXPERIMENTAL SET-UPS ALLOWING CHARACTERIZING THE INFLUENCE OF NANO-SCALE SUBSTRATE TOPOGRAPHY ONTO THE FLATTENING AND SOLIDIFICATION OF MICROMETER AND MILLIMETER SIZED MOLTEN DROPLET
International Heat Transfer Conference 13, Vol.0, 2006, issue
Michel Vardelle, Y. Tanaka, J. Cedelle, Pierre Fauchais
Rotational Temperature of Oxygen in a High-Power Inductively Coupled Plasma
Progress in Plasma Processing of Materials, 1997, Vol.1, 1997, issue
Berthold Michelt, Gunter Lins , Robert J. Seebock