Suscripción a Biblioteca: Guest
Portal Digitalde Biblioteca Digital eLibros Revistas Referencias y Libros de Ponencias Colecciones
High Temperature Material Processes: An International Quarterly of High-Technology Plasma Processes
SJR: 0.137 SNIP: 0.341 CiteScore™: 0.43

ISSN Imprimir: 1093-3611
ISSN En Línea: 1940-4360

High Temperature Material Processes: An International Quarterly of High-Technology Plasma Processes

DOI: 10.1615/HighTempMatProc.v7.i2.100
11 pages

INFLUENCE OF DC PLASMA PREHEATING ON OXIDE LAYERS FORMED BY FURNACE HEATING ON LOW CARBON STEEL SUBSTRATES AND RESULTING ADHESION/COHESION OF ALUMINA COATINGS

S. Valette
SPCTS - Science des precedes Ceramique et de Traitements de Surface - UMR CNRS 6638 - University of Limoges -123 Avenue Albert Thomas - 87060 Limoges Cedex - France
Alain Denoirjean
Equipe Plasma Laser Matériaux, ESA CNRS 6015, 87060 Limoges Cedex, France
Pierre Lefort
Laboratoire Science des Precedes Ceramiques et Traitements de Surface UMR CNRS 6638 123 Avenue Albert-Thomas F-87060 Limoges Cedex, France
Pierre Fauchais
Laboratoire Sciences des Procedes Ceramiques et de Traitements de Surface UMR CNRS 6638 University of Limoges 123 avenue Albert Thomas, 87060 LIMOGES - France

SINOPSIS

In plasma spraying the preheating of low carbon steel substrates (X40) with a rough surface resulting from grit blasting, has received an increased interest because it promotes the adhesion and cohesion (A/C) of alumina coatings. Earlier works have reported the generation of a duplex Fе3O4/Fе2O3 layer after preheating by the d.c. plasma jet. Improved A/C values were obtained for an increase in Fе3O4 content in the oxide layer. Much improved adherence values were achieved with alumina spayed on Fe1-xO layers. In this case, the Adhesion/cohesion values obtained on smooth substrate (Ra ~ 0.1 mm) were good (~ 40 MPa) and close to those obtained on rough ones (Ra ~ 5 mm). First the time evolution of the Fe1-xO layer thickness and morphology produced in a controlled atmosphere furnace was studied. Then the influence of the plasma preheating of the wilstite layers was studied by SEM, and XRD analyses. XRD analysis results indicated a slight variation in the oxide phases depending on the preheating cycles. Fе3O4 was found to increase when a decomposition of Fe1-xO into Fе3O4 was observed.


Articles with similar content:

INFLUENCE OF DC PLASMA PREHEATING ON OXIDE LAYERS FORMED BY FURNACE HEATING ON LOW CARBON STEEL SUBSTRATES AND RESULTING ADHESION/COHESION OF ALUMINA COATINGS
Progress in Plasma Processing of Materials, 2003, Vol.0, 2003, issue
Pierre Lefort, S. Valette, Alain Denoirjean, Pierre Fauchais
TEOS/O2 GAS PRESSURE AS A CHEMICAL COMPOSITION ADJUSTER OF PLASMA DEPOSITED SIO2 THIN FILMS
High Temperature Material Processes: An International Quarterly of High-Technology Plasma Processes, Vol.9, 2005, issue 2
Dimitrious E. Rapakoulias, Dimitris Mataras, Ch. Voulgaris, E. Amanatides, A. Panou
REDUCTION OF TUNGSTEN PRECURSORS IN INDUCTIVELY COUPLED RF DISCHARGE
Progress in Plasma Processing of Materials, 2003, Vol.0, 2003, issue
J. Zila, Jan Janca, Vlastimil Brozek, Marek Elias
INFLUENCE OF NICKEL OXIDE AMOUNT ON ELECTRICAL PARAMETERS AND STABILITY OF SUPERCAPACITORS
High Temperature Material Processes: An International Quarterly of High-Technology Plasma Processes, Vol.14, 2010, issue 3
Z . Kavaliauskas, L. L. Pranevicius, L. Marcinauskas, Liudas Pranevicius, Pranas Valatkevicius
INFLUENCE OF SUBSTRATE SURFACE OXIDATION STAGE ON THE MORPHOLOGY AND FLATTENING OF SPLATS
High Temperature Material Processes: An International Quarterly of High-Technology Plasma Processes, Vol.7, 2003, issue 2
J. C. Labbe, A. A. Syed, Alain Denoirjean, Pierre Fauchais, P. Denoirjean