Suscripción a Biblioteca: Guest
Portal Digitalde Biblioteca Digital eLibros Revistas Referencias y Libros de Ponencias Colecciones
International Journal for Multiscale Computational Engineering
Factor de Impacto: 1.016 Factor de Impacto de 5 años: 1.194 SJR: 0.554 SNIP: 0.68 CiteScore™: 1.18

ISSN Imprimir: 1543-1649
ISSN En Línea: 1940-4352

International Journal for Multiscale Computational Engineering

DOI: 10.1615/IntJMultCompEng.v5.i2.60
pages 129-140

Modeling the Interaction between Plasticity and the Austenite-Martensite Transformation

Varvara G. Kouznetsova
Department of Mechanical Engineering, Eindhoven University of Technology P.O. Box 513, 5600 MB Eindhoven; and Netherlands Institute for Metals Research, Rotterdamseweg 137 2628 AL Delft, The Netherlands
Marc Geers
Dept. of Mechanical Engineering Eindhoven University of Technology PO Box 513, 5600 MB Eindhoven The Netherlands

SINOPSIS

Many advanced steels, such as high strength steels and TRIP steels, owe their excellent combination of strength and ductility to the complex microstructural behaviour involving the austenite to martensite phase transformation. In this paper a physically-based model for martensitic transformation induced plasticity at the grain level is presented. In terms of output, the model provides the evolution of the overall martensite volume fraction within a grain and the overall stress-strain response of a grain, as well as the martensite volume fractions produced on each of the potential transformation systems. The model directly incorporates the coupling between elasticity, plasticity, plastic history inheritance and transformation. In this work, special attention is given to a proper incorporation of the interaction between the plastic deformation of austenite and the martensitic transformation, which is known to be twofold. On one hand, the plastic deformation of austenite is known to promote the transformation by creation of additional nucleation sites for the transformation, on the other hand the dislocation foresting leads to the mechanical stabilization of austenite, thus retarding the transformation. These two effects are incorporated in the model. To illustrate the performance of the model it has been applied to the deformation and transformation of a single austenitic grain loaded in different crystallographic directions, focusing on the transformation after the plastic prestraining of austenite.


Articles with similar content:

PREDICTION OF DISTRIBUTION OF MICROSTRUCTURAL PARAMETERS INMETALLIC MATERIALS DESCRIBED BY DIFFERENTIAL EQUATIONS WITH RECRYSTALLIZATION TERM
International Journal for Multiscale Computational Engineering, Vol.17, 2019, issue 3
Jan Kusiak, Maciej Pietrzyk, Danuta Szeliga, Piotr Oprocha, Paweł Przybyłowicz, Lukasz Rauch, Natalia Czyzewska, Paweł Morkisz
NUMERICAL MODELING OF PHASE TRANSFORMATION IN DUAL PHASE (DP) STEEL AFTER HOT ROLLING AND LAMINAR COOLING
International Journal for Multiscale Computational Engineering, Vol.12, 2014, issue 5
Krzysztof Bzowski, Maciej Pietrzyk, Monika Pernach
ESSENTIAL FEATURES OF FINE SCALE BOUNDARY CONDITIONS FOR SECOND GRADIENT MULTISCALE HOMOGENIZATION OF STATISTICAL VOLUME ELEMENTS
International Journal for Multiscale Computational Engineering, Vol.10, 2012, issue 5
David L. McDowell, Darby Luscher, Curt Bronkhorst
GEOMETRIC OPTIMIZATION BASED ON THE CONSTRUCTAL DESIGN OF PERFORATED THIN PLATES SUBJECT TO BUCKLING
Computational Thermal Sciences: An International Journal, Vol.4, 2012, issue 2
Luiz Alberto O. Rocha, L. A. Isoldi, A. L. G. Correia, E. D. dos Santos, M. V. Real, J. Vaz
CYCLICAL HEAT CONDUCTION IN MELTING AND FREEZING OF COMPOSITE SLABS OF DIFFERENT PHASE CHANGE MATERIALS
International Heat Transfer Conference 10, Vol.17, 1994, issue
Z. X. Gong, Arun S. Mujumdar