Suscripción a Biblioteca: Guest
Portal Digitalde Biblioteca Digital eLibros Revistas Referencias y Libros de Ponencias Colecciones
Atomization and Sprays
Factor de Impacto: 1.262 Factor de Impacto de 5 años: 1.518 SJR: 0.814 SNIP: 1.18 CiteScore™: 1.6

ISSN Imprimir: 1044-5110
ISSN En Línea: 1936-2684

Volumes:
Volumen 29, 2019 Volumen 28, 2018 Volumen 27, 2017 Volumen 26, 2016 Volumen 25, 2015 Volumen 24, 2014 Volumen 23, 2013 Volumen 22, 2012 Volumen 21, 2011 Volumen 20, 2010 Volumen 19, 2009 Volumen 18, 2008 Volumen 17, 2007 Volumen 16, 2006 Volumen 15, 2005 Volumen 14, 2004 Volumen 13, 2003 Volumen 12, 2002 Volumen 11, 2001 Volumen 10, 2000 Volumen 9, 1999 Volumen 8, 1998 Volumen 7, 1997 Volumen 6, 1996 Volumen 5, 1995 Volumen 4, 1994 Volumen 3, 1993 Volumen 2, 1992 Volumen 1, 1991

Atomization and Sprays

DOI: 10.1615/AtomizSpr.v8.i1.50
pages 83-107

CHARACTERIZATION OF HIGH-INJECTION-PRESSURE DIESEL SPRAYS WITH RELATION TO PARTICULATE AND NOx EMISSIONS

T. F. Su
Engine Research Center, University of Wisconsin—Madison, Madison, Wisconsin, USA
Patrick V. Farrell
Engine Research Center, University of Wisconsin—Madison, Madison, Wisconsin, USA

SINOPSIS

The transient characteristics of high-injection-pressure diesel fuel sprays have been investigated by high-speed photography. An off-engine fuel injection system with a hydraulic unit injector was designed for spray visualization experiments. Experiments were conducted using different geometry nozzles under different operating conditions to investigate the effects of injection pressure, nozzle inlet condition, nozzle injection angle, and nozzle hole size on spray characteristics. Measurement of spray tip penetration length and spray angle were made based on the spray images. The Sauter mean diameter (SMD) averaged over the spray was measured using a light extinction method. The results of these experiments show that spray geometry ( penetration length and cone angle) is sensitive to small changes in operating conditions and injector geometry. Higher injection pressures produced larger penetration, smaller spray cone angles, and smaller overall average SMD. Smaller nozzle hole sizes and smaller injection angle nozzles also produced smaller droplet sizes.
Previous results from engine emissions tests using the same injector under similar operating conditions were examined in light of the observed spray characteristics. While the engine emission results are affected by many parameters related to the fuel injection system as well as many which are unrelated to the injection system, the results of these comparisons indicate that spray SMD and spatial distribution have a significant effect on engine emissions for the conditions tested.


Articles with similar content:

DEVELOPMENT OF MICRO-DIESEL INJECTOR NOZZLES VIA MEMS TECHNOLOGY AND EFFECTS ON SPRAY CHARACTERISTICS
Atomization and Sprays, Vol.13, 2003, issue 5&6
Michael L. Corradini, Seunghyun Baik, James P Blanchard
EXPERIMENTAL INVESTIGATION OF SPRAY CHARACTERISTICS OF DIESEL-METHANOL-WATER EMULSION
Atomization and Sprays, Vol.25, 2015, issue 8
Wuqiang Wang, Shenteng Cao, Dongyin Wu, Junjie Yan, Zhenzhou Pang
EFFECT OF SPLIT INJECTION ON THE MACROSCOPIC DEVELOPMENT AND ATOMIZATION CHARACTERISTICS OF A DIESEL SPRAY INJECTED THROUGH A COMMON-RAIL SYSTEM
Atomization and Sprays, Vol.16, 2006, issue 5
Rolf D. Reitz, Chang Sik Lee, Sungwook Park
SPRAY VISUALIZATION AND HYDRAULIC CHARACTERIZATION OF THE HOLES OF A FIVE-HOLE, VALVE-COVERED-ORIFICE NOZZLE OF AN ELECTRONICALLY CONTROLLED DIESEL INJECTOR
Atomization and Sprays, Vol.6, 1996, issue 3
D. Laforgia, V. Damiani, R. Campanella
DROP SIZE MEASUREMENTS IN HEAVY OIL SPRAYS FROM PRESSURE-SWIRL NOZZLES
Atomization and Sprays, Vol.6, 1996, issue 4
Cesar Dopazo, Javier Ballester