Suscripción a Biblioteca: Guest
Portal Digitalde Biblioteca Digital eLibros Revistas Referencias y Libros de Ponencias Colecciones
Atomization and Sprays
Factor de Impacto: 1.262 Factor de Impacto de 5 años: 1.518 SJR: 0.814 SNIP: 1.18 CiteScore™: 1.6

ISSN Imprimir: 1044-5110
ISSN En Línea: 1936-2684

Volumes:
Volumen 29, 2019 Volumen 28, 2018 Volumen 27, 2017 Volumen 26, 2016 Volumen 25, 2015 Volumen 24, 2014 Volumen 23, 2013 Volumen 22, 2012 Volumen 21, 2011 Volumen 20, 2010 Volumen 19, 2009 Volumen 18, 2008 Volumen 17, 2007 Volumen 16, 2006 Volumen 15, 2005 Volumen 14, 2004 Volumen 13, 2003 Volumen 12, 2002 Volumen 11, 2001 Volumen 10, 2000 Volumen 9, 1999 Volumen 8, 1998 Volumen 7, 1997 Volumen 6, 1996 Volumen 5, 1995 Volumen 4, 1994 Volumen 3, 1993 Volumen 2, 1992 Volumen 1, 1991

Atomization and Sprays

DOI: 10.1615/AtomizSpr.v20.i12.40
pages 1065-1076

EXPERIMENTAL INVESTIGATION OF NEAR NOZZLE SPRAY STRUCTURE AND VELOCITY FOR A GDI HOLLOWCONE SPRAY

D. Martin
Institute of Heat and Mass Transfer, RWTH Aachen University, Eilfschornsteinstr. 18, 52062 Aachen, Germany
M. Cardenas
Institute of Heat and Mass Transfer, RWTH Aachen University, 52062 Aachen, Germany
Philipp Pischke
Institute of Heat and Mass Transfer, RWTH Aachen University, Augustinerbach 6, 52062 Aachen, Germany
Reinhold Kneer
Institute of Heat and Mass Transfer, RWTH Aachen University, Augustinerbach 6, 52062 Aachen, Germany

SINOPSIS

Previous experiments and numerical investigations of engine sprays show string-like structures at the exit of outwardly opening nozzles applied in gasoline direct injection (GDI) engines. These structures were further analyzed using visualization techniques and laser correlation velocimetry (LCV). Ambient conditions of 0.1 MPa and 300 K were chosen for all experiments, while injection pressure and injector energizing time were varied to resolve the influence of injection parameters on structure and velocity. Through application of a visualization measurement technique with a far-field microscope the string-like structures and their evolution during the injection period have been identified. In addition the influence of the injection parameters on the shape and location of the strings has been analyzed. After resolving the differences in string structure, the influence of the string structure on the velocity distribution at the nozzle exit was investigated for obtaining a correlation between string structure and spray velocity. Finally, the dependency of spray exit velocity on injection pressure and injection duration was determined. The information about string structure and nozzle exit velocity can be used to deduce different influences on the primary breakup of a hollow cone spray generated by an outwardly opening nozzle.


Articles with similar content:

EXPERIMENTAL INVESTIGATIONS ON A PIEZO-ACTIVATED HOLLOW CONE INJECTOR − PART I: MEASUREMENT OF NEEDLE LIFT AND ITS INFLUENCE ON SPRAY MORPHOLOGY
Atomization and Sprays, Vol.24, 2014, issue 10
Graham Wigley, Konstantinos Boulouchos, B. Schneider, Andreas Schmid
INFLUENCE OF PIEZO-DRIVEN SYNTHETIC JET ON WATER SPRAY BEHAVIOR
Atomization and Sprays, Vol.27, 2017, issue 8
Matteo Chiatto, Luca Marchitto, Luigi de Luca, G. Valentino
IMPACT OF PHYSICAL PROPERTIES ON PRIMARY BREAKUP FOR A DIESEL NOZZLE CONFIGURATION
Atomization and Sprays, Vol.21, 2011, issue 3
F. Mathieu, D. Martin, Reinhold Kneer, Manuel Armin Reddemann
THE EFFECT OF INITIAL AMBIENT TURBULENCE LEVELS ON ISO-OCTANE INJECTION SPRAYS
Atomization and Sprays, Vol.21, 2011, issue 10
H. M. Thompson, P. H. Gaskell, Malcolm Lawes, I. Elbadawy
Characterization of Direct-Injection Gasoline Sprays under Different Ambient and Fuel Injection Conditions
International Journal of Fluid Mechanics Research, Vol.24, 1997, issue 4-6
J.-H. Yoo, Fu-Quan Zhao, K.-S. Lee, Ming Chia Lai, Y. Liu