Suscripción a Biblioteca: Guest
Portal Digitalde Biblioteca Digital eLibros Revistas Referencias y Libros de Ponencias Colecciones
Atomization and Sprays
Factor de Impacto: 1.737 Factor de Impacto de 5 años: 1.518 SJR: 0.814 SNIP: 1.18 CiteScore™: 2.2

ISSN Imprimir: 1044-5110
ISSN En Línea: 1936-2684

Volumes:
Volumen 30, 2020 Volumen 29, 2019 Volumen 28, 2018 Volumen 27, 2017 Volumen 26, 2016 Volumen 25, 2015 Volumen 24, 2014 Volumen 23, 2013 Volumen 22, 2012 Volumen 21, 2011 Volumen 20, 2010 Volumen 19, 2009 Volumen 18, 2008 Volumen 17, 2007 Volumen 16, 2006 Volumen 15, 2005 Volumen 14, 2004 Volumen 13, 2003 Volumen 12, 2002 Volumen 11, 2001 Volumen 10, 2000 Volumen 9, 1999 Volumen 8, 1998 Volumen 7, 1997 Volumen 6, 1996 Volumen 5, 1995 Volumen 4, 1994 Volumen 3, 1993 Volumen 2, 1992 Volumen 1, 1991

Atomization and Sprays

DOI: 10.1615/AtomizSpr.v6.i3.20
pages 257-284

SPRAY VISUALIZATION AND HYDRAULIC CHARACTERIZATION OF THE HOLES OF A FIVE-HOLE, VALVE-COVERED-ORIFICE NOZZLE OF AN ELECTRONICALLY CONTROLLED DIESEL INJECTOR

R. Campanella
Istituto di Macchine ed Energetica, Politecnico di Bari, Bari, Italy
V. Damiani
ELASIS, Sistema Ricerche FIAT nel Mezzogiorno, Centre Alimentazione Motori, Z.I. Modugno, Modugno, Italy
D. Laforgia
Dipartimento di lngegneria dell'Innovazione, Universita di Lecce, Lecce, Italy

SINOPSIS

A study of the spray of a standard, five-hole, valve-covered-orifice (V.C.O.) nozzle for D.I. diesel engines has been carried out, several pictures of the spray coming from each hole have been taken using the back-light photography technique. Injected volume and duration, supply pressure, spray penetration, angle, and diameter, and flash delay from start of injection have been measured; each spray depends strongly on the needle lift. The causes of such differences have been attributed to the different inclination of the holes, the asymmetric feeding condition of the holes (due to the eccentricity between needle and nozzle), and the microdefects caused by the drilling operation.


Articles with similar content:

EXPERIMENTAL STUDY ON VELOCITY DISTRIBUTION OF POSTIMPINGEMENT DIESEL SPRAY ON A WALL. PART 1: EFFECT OF IMPINGEMENT ANGLE ON FLOW PATTERN
Atomization and Sprays, Vol.24, 2014, issue 8
Masataka Arai, Yoshio Zama, Tomohiko Furuhata, Mohd Zaid Akop, Kazuma Sugawara
CFD Study of Needle Motion Influence on the Spray Conditions of Single-Hole Injectors
Atomization and Sprays, Vol.21, 2011, issue 1
P. Fajardo, Xandra Margot, S. Patouna, Sergio Hoyas
EFFECT OF NOZZLE HOLE GEOMETRY ON NON-EVAPORATING DIESEL SPRAY CHARACTERISTICS AT HIGH-PRESSURE INJECTION
Atomization and Sprays, Vol.22, 2012, issue 1
Jangsik Kong, Choongsik Bae
CHARACTERIZATION OF PROTOTYPE HIGH-PRESSURE SWIRL INJECTOR NOZZLES, PART II: CFD EVALUATION OF INTERNAL FLOW
Atomization and Sprays, Vol.10, 2000, issue 2
Sangmin Choi, Changsoo Jang, Choongsik Bae
INFLUENCE OF VORTEX FLOW AND CAVITATION ON NEAR-NOZZLE DIESEL SPRAY DISPERSION ANGLE
Atomization and Sprays, Vol.19, 2009, issue 3
Manolis Gavaises, A. Andriotis