Suscripción a Biblioteca: Guest
Portal Digitalde Biblioteca Digital eLibros Revistas Referencias y Libros de Ponencias Colecciones
Atomization and Sprays
Factor de Impacto: 1.262 Factor de Impacto de 5 años: 1.518 SJR: 0.814 SNIP: 1.18 CiteScore™: 1.6

ISSN Imprimir: 1044-5110
ISSN En Línea: 1936-2684

Volumes:
Volumen 29, 2019 Volumen 28, 2018 Volumen 27, 2017 Volumen 26, 2016 Volumen 25, 2015 Volumen 24, 2014 Volumen 23, 2013 Volumen 22, 2012 Volumen 21, 2011 Volumen 20, 2010 Volumen 19, 2009 Volumen 18, 2008 Volumen 17, 2007 Volumen 16, 2006 Volumen 15, 2005 Volumen 14, 2004 Volumen 13, 2003 Volumen 12, 2002 Volumen 11, 2001 Volumen 10, 2000 Volumen 9, 1999 Volumen 8, 1998 Volumen 7, 1997 Volumen 6, 1996 Volumen 5, 1995 Volumen 4, 1994 Volumen 3, 1993 Volumen 2, 1992 Volumen 1, 1991

Atomization and Sprays

DOI: 10.1615/AtomizSpr.2014011350
pages 47-80

ATOMIZATION MODELLING OF LIQUID JETS USING A TWO-SURFACE-DENSITY APPROACH

Bejoy Mandumpala Devassy
IFP Energies Nouvelles, let 4 Avenue de Bois-Preau, 92852 Rueil-Malmaison, France
Chawki Habchi
IFP Energies Nouvelles, let 4 Avenue de Bois-Preau, 92852 Rueil-Malmaison, France
Eric Daniel
Aix-Marseille Universite, IUSTI, 5 rue E. Fermi 13453 Marseille Cedex 13, France

SINOPSIS

In internal combustion engines, the liquid fuel injection is an essential step for the air/fuel mixture preparation and the combustion process. Indeed, the structure of the liquid jet coming out from the injector plays a key role in the proper mixing of the fuel with the gas in the combustion chamber. The present work focuses on the liquid jet atomization phenomena under diesel engine conditions. Under these conditions, liquid jet morphology is assumed, including a separate liquid phase (i.e., a liquid core) and a dispersed liquid phase (i.e., a spray). This article describes the developmental stages of a new atomization model, for a high-speed liquid jet, based on an Eulerian-Eulerian two-fluid approach. The atomization phenomena are modelled by defining different surface density equations for the liquid core and the spray droplets. This new model has been coupled with a turbulent and highly compressible two-fluid system of equations. The process of ligament breakup and its subsequent breakup into droplets are handled by acquiring knowledge from the available high-fidelity experiments and numerical simulations. In the dense region of the liquid jet, the atomization is modelled as a dispersion process due to the stretching of the interface, from the liquid side in addition to the gas side. The model results have been compared to a recently published DNS results under typical direct injection diesel engine conditions. In particular, it has been shown that the interface instabilities and the turbulence in the leading tip of the liquid core play a major role in the primary atomization of diesel jets.


Articles with similar content:

DIRECT NUMERICAL AND LARGE-EDDY SIMULATION OF PRIMARY ATOMIZATION IN COMPLEX GEOMETRIES
Atomization and Sprays, Vol.23, 2013, issue 11
Peter Brady, Mark Owkes, Olivier Desjardins, Jeremy McCaslin
TWO-FLUID MODELING OF SPRAY PENETRATION AND DISPERSION UNDER DIESEL ENGINE CONDITIONS
Atomization and Sprays, Vol.15, 2005, issue 3
Venkatraman Iyer, John P. Abraham
END OF INJECTION PROCESS IN A SINGLE-HOLE DIESEL INJECTOR
Atomization and Sprays, Vol.28, 2018, issue 1
V. Garaniya, P. A. Brandner, Mohammadmahdi Ghiji, P. Hield, Laurie Goldsworthy
INJECTION, ATOMIZATION AND MIXING OF PROPELLANTS IN LIQUID ROCKET ENGINES USING COXIAL INJECTORS
ICLASS 94
Proceedings of the Sixth International Conference on Liquid Atomization and Spray Systems, Vol.0, 1994, issue
G. Krulle, W. Mayer
A NEW MODEL FOR TURBULENT FLOWS WITH LARGE DENSITY FLUCTUATIONS: APPLICATION TO LIQUID ATOMIZATION
Atomization and Sprays, Vol.17, 2007, issue 4
Pierre-Arnaud Beau, R. Borghi, Francois-Xavier Demoulin, Arnaud Mura, Gregory Blokkeel