Abonnement à la biblothèque: Guest
Portail numérique Bibliothèque numérique eBooks Revues Références et comptes rendus Collections
Journal of Porous Media
Facteur d'impact: 1.061 Facteur d'impact sur 5 ans: 1.151 SJR: 0.504 SNIP: 0.671 CiteScore™: 1.58

ISSN Imprimer: 1091-028X
ISSN En ligne: 1934-0508

Volumes:
Volume 22, 2019 Volume 21, 2018 Volume 20, 2017 Volume 19, 2016 Volume 18, 2015 Volume 17, 2014 Volume 16, 2013 Volume 15, 2012 Volume 14, 2011 Volume 13, 2010 Volume 12, 2009 Volume 11, 2008 Volume 10, 2007 Volume 9, 2006 Volume 8, 2005 Volume 7, 2004 Volume 6, 2003 Volume 5, 2002 Volume 4, 2001 Volume 3, 2000 Volume 2, 1999 Volume 1, 1998

Journal of Porous Media

DOI: 10.1615/JPorMedia.v20.i9.40
pages 823-839

THE EFFECT OF INLET CONDITION ON THE COMBUSTION IN A POROUS–FREE FLAME BURNER

Seyed Abdolmehdi Hashemi
Department of Mechanical Engineering, University of Kashan, Kashan, Iran; Energy Research Institute, University of Kashan, Kashan, Iran
Majid Nikfar
Department of Mechanical Engineering, University of Kashan, Kashan, Iran; Energy Research Institute, University of Kashan, Kashan, Iran; Department of Mechanical Engineering, Isfahan University of Technology, Isfahan, Iran

RÉSUMÉ

Premixed combustion in "porous" and novel "porous–free flame" burners are studied using numerical simulations in an axisymmetric combustion chamber. The porous medium is perforated along the axis to create a combination of a free flame and porous burner. The governing equations are solved using the finite volume numerical method. A reduced chemical mechanism and a realizable k-ε turbulence model are used for simulation. In order to validate the numerical results, both burners have been constructed and tested. The obtained numerical results showed a good agreement with the experimental data. The numerical results showed that the flame of the porous–free flame burner has a greater stability limit than that of the porous burner. The effect of the inlet condition is studied so that with increasing equivalence ratio, the lower stability limit always increases, but the upper stability limit first increases and then decreases. The maximum upper limit of stability is obtained in the equivalence ratio of 0.9. The effect of change in temperature of the inlet mixture (300, 450, and 600 K) on flame location and flame stability limit is investigated. It is observed that the flame stability limit increases with increasing inlet mixture temperature.


Articles with similar content:

CFD BASED EVALUATION OF THERMODYNAMIC PARAMETERS AND FLOW FIELD FOR HYDROGEN AIR DEFLAGRATIONS
Proceedings of the 24th National and 2nd International ISHMT-ASTFE Heat and Mass Transfer Conference (IHMTC-2017), Vol.0, 2017, issue
Aditya Karanam, Pavan K. Sharma, Sunil Ganju
TURBULENCE-CHEMISTRY INTERACTION CALCULATIONS FOR IMPROVED NOx PREDICTIONS
International Journal of Energy for a Clean Environment, Vol.6, 2005, issue 3
P. Arfi, Yeshayahou Levy
NUMERICAL ANALYSIS OF COHERENT STRUCTURES IN BIDIRECTIONAL SWIRL COMBUSTION CHAMBER
Computational Thermal Sciences: An International Journal, Vol.8, 2016, issue 3
V. Aghakashi, Mohammad Hassan Saidi, P. M. Keshavarz
MODELLING AND SIMULATION OF LEAN PREMIXED TURBULENT METHANE/HYDROGEN/AIR FLAMES FOR TWO FLOW CONFIGURATIONS
ICHMT DIGITAL LIBRARY ONLINE, Vol.13, 2008, issue
Friedrich Dinkelacker, Jennifer X. Wen, B. Manickam, S. P. R. Muppala, N. K. Aluri
3-D NUMERICAL MODELING AND EXPERIMENTAL INVESTIGATION OF A PARTIAL PREMIX-TYPE POROUS MEDIUM BURNER USING LIQUEFIED PETROLEUM GAS FUEL
Journal of Porous Media, Vol.13, 2010, issue 7
Abdulmajeed A. Mohamad, R. Zakaria, M. Abdul Mujeebu, M. Z. Abu Bakar, R. M. N. Muhad, M. Z. Abdullah