Abonnement à la biblothèque: Guest
Portail numérique Bibliothèque numérique eBooks Revues Références et comptes rendus Collections
Journal of Porous Media
Facteur d'impact: 1.49 Facteur d'impact sur 5 ans: 1.159 SJR: 0.43 SNIP: 0.671 CiteScore™: 1.58

ISSN Imprimer: 1091-028X
ISSN En ligne: 1934-0508

Volumes:
Volume 23, 2020 Volume 22, 2019 Volume 21, 2018 Volume 20, 2017 Volume 19, 2016 Volume 18, 2015 Volume 17, 2014 Volume 16, 2013 Volume 15, 2012 Volume 14, 2011 Volume 13, 2010 Volume 12, 2009 Volume 11, 2008 Volume 10, 2007 Volume 9, 2006 Volume 8, 2005 Volume 7, 2004 Volume 6, 2003 Volume 5, 2002 Volume 4, 2001 Volume 3, 2000 Volume 2, 1999 Volume 1, 1998

Journal of Porous Media

DOI: 10.1615/JPorMedia.2019028864
pages 167-181

NUMERICAL INVESTIGATIONS ON FORMATION CONDITIONS OF THE THIEF ZONE BY LEVEL SET METHOD

Shuoliang Wang
School of Energy Resources, China University of Geosciences, Beijing, 100083, China; Key Laboratory of Marine Reservoir Evolution and Hydrocarbon Enrichment Mechanism, Ministry of Education
Hui Zhao
College of Petroleum Engineering, Yangtze University, 1 Nanhuan Road Jingzhou Hubei, 434023, China
Chunlei Yu
Shengli Oilfield Exploration and Development Research Institute, Dongying, Shandong, 257000, China

RÉSUMÉ

The injection water flowing along the thief zone directly affects oil field development efficiency and oil production. The formation condition of the thief zone is an issue worth studying. In this paper, first, the two-phase displacement experimental results are obtained through a one-dimensional microtube experiment and a two-dimensional glass etching plate experiment. Then, based on the experimental device size, a numerical simulation model of the Level set is established. By comparing the calculated results of the Level set method with the laboratory experimental results, it is proved that the Level set calculation method can be used to calculate the free surface tracking problem of oil–water two-phase in porous media. Based on this foundation, a mathematical model of parallel tubes is established using the Level set method. The influence factors of injection water channeling are analyzed in a microcosmic viewpoint. After calculating parallel microtube numerical simulation models, it is found that the greater the displacement pressure, the greater the crude oil viscosity, the bigger the wetting angle, the smaller the interfacial tension, and the easier it is to form the thief zone. In this paper, the authors are first to innovatively present the critical tube diameter ratios in different conditions and the formation conditions of channeling under different pressures, oil–water viscosity ratios, wetting angles, and interfacial tensions in a microcosmic viewpoint.


Articles with similar content:

THE STUDY ON THE DISTRIBUTION LAW OF INTERWELL PRESSURE GRADIENT CONSIDERING THE INFLUENCE OF PROFILE CONTROL AND WATER SHUTOFF
Journal of Porous Media, Vol.21, 2018, issue 3
Qiang Fu, Shuoliang Wang, Zhimin Du
INVESTIGATION OF APPLICABILITY OF DUAL-POROSITY MODEL FOR POLYMER FLOODING SIMULATION
Journal of Porous Media, Vol.21, 2018, issue 13
Behnam Sedaee Sola, Assila Taymourtash
THE CHARACTERISTICS OF POSTIMPINGEMENT DIESEL SPRAY, PART I: PENETRATION AND VOLUME
Atomization and Sprays, Vol.12, 2002, issue 4
Masataka Arai, Kyungnam Ko
Viscous Fingering During Miscible Liquid-Liquid Displacement in Porous Media
International Journal of Fluid Mechanics Research, Vol.26, 1999, issue 5-6
M. R. Islam
RELATIVE PERMEABILITIES CHARACTERIZATION IN CHEMICAL FLOODING WITH THE CONSIDERATION OF VISCOSITY RATIO AND INTERFACIAL TENSION BY A PORE-SCALE NETWORK MODEL
Journal of Porous Media, Vol.18, 2015, issue 11
Qingjie Liu, Pingping Shen