Abonnement à la biblothèque: Guest
Portail numérique Bibliothèque numérique eBooks Revues Références et comptes rendus Collections
Journal of Enhanced Heat Transfer
Facteur d'impact: 0.562 Facteur d'impact sur 5 ans: 0.605 SJR: 0.211 SNIP: 0.361 CiteScore™: 0.33

ISSN Imprimer: 1065-5131
ISSN En ligne: 1026-5511

Volumes:
Volume 26, 2019 Volume 25, 2018 Volume 24, 2017 Volume 23, 2016 Volume 22, 2015 Volume 21, 2014 Volume 20, 2013 Volume 19, 2012 Volume 18, 2011 Volume 17, 2010 Volume 16, 2009 Volume 15, 2008 Volume 14, 2007 Volume 13, 2006 Volume 12, 2005 Volume 11, 2004 Volume 10, 2003 Volume 9, 2002 Volume 8, 2001 Volume 7, 2000 Volume 6, 1999 Volume 5, 1998 Volume 4, 1997 Volume 3, 1996 Volume 2, 1995 Volume 1, 1994

Journal of Enhanced Heat Transfer

DOI: 10.1615/JEnhHeatTransf.2011003351
pages 75-86

AN EXPERIMENTAL STUDY OF BOILING HEAT TRANSFER ENHANCEMENT OF MESH-ON-FIN TUBES

Liang-Han Chien
National Taipei University of Technology
H.-L. Hwang
Department of Energy and Refrigerating Air-conditioning Engineering, National Taipei University of Technology, 1, Sec. 3, Chung-Hsaio E. Rd., Taipei 106, Taiwan

RÉSUMÉ

This study investigated a new enhanced boiling surface made by wrapping wire mesh on low-fin tubes. Pool boiling performance of the new enhanced tubes was tested with refrigerant 134a at 5,10, and 26.67°C saturation temperature for 6−48 kW/m2 heat flux. Brass or copper mesh of 80,100, or 120 mesh per inch was wrapped around finned tubes of 42, 50, or 60 FPI (fins per inch). The fin heights were either 0.2 mm or 0.4 mm. The test results show that mesh-covered fin tubes yielded significantly enhanced boiling performance. The influence of fin geometry is more pronounced with mesh than without mesh. The preferred mesh size decreases with decreasing heat flux. The surface made by wrapping brass mesh of 100 mesh per inch on 60 FPI tube having 0.4 mm fin height yielded the best boiling performance. It enhanced the boiling heat transfer coefficient by 3−8 fold at 5−26.7°C as compared with the smooth tube.


Articles with similar content:

Enhancement of Pool Boiling on Structured Surfaces Using HFC-4310 and Water
Journal of Enhanced Heat Transfer, Vol.11, 2004, issue 1
Liang-Han Chien, C. C. Chang
Compound Augmentation of Pool Boiling on Three Selected Commercial Tubes
Journal of Enhanced Heat Transfer, Vol.7, 2000, issue 5
Michael M. Ohadi, J. Darabi, Serguei V. Dessiatoun
NATURAL CONVECTION HEAT TRANSFER FROM SQUARE PIN FIN AND PLATE FIN HEAT SINKS SUBJECT TO THE INFLUENCE OF ORIENTATION
International Heat Transfer Conference 13, Vol.0, 2006, issue
R. T. Huang, Chi-Chuan Wang, Wen-Jenn Sheu
DENDRITICALLY ORDERED NANO-PARTICLES IN A MICRO-POROUS STRUCTURE FOR ENHANCED BOILING
International Heat Transfer Conference 13, Vol.0, 2006, issue
Mamoun Muhammed, R. Furberg, Shanghua Li, Björn Palm, Muhammet S. Toprak
CONDENSATION PRESSURE DROP CHARACTERISTICS OF R410A INSIDE HORIZONTAL THREE-DIMENSIONAL ENHANCED TUBES
International Heat Transfer Conference 16, Vol.7, 2018, issue
Yan He, Zhi-chuan Sun, Wei Chen, Wei Li, Ruiheng Guo