Abonnement à la biblothèque: Guest
Portail numérique Bibliothèque numérique eBooks Revues Références et comptes rendus Collections
Journal of Enhanced Heat Transfer
Facteur d'impact: 0.562 Facteur d'impact sur 5 ans: 0.605 SJR: 0.211 SNIP: 0.361 CiteScore™: 0.33

ISSN Imprimer: 1065-5131
ISSN En ligne: 1026-5511

Volumes:
Volume 26, 2019 Volume 25, 2018 Volume 24, 2017 Volume 23, 2016 Volume 22, 2015 Volume 21, 2014 Volume 20, 2013 Volume 19, 2012 Volume 18, 2011 Volume 17, 2010 Volume 16, 2009 Volume 15, 2008 Volume 14, 2007 Volume 13, 2006 Volume 12, 2005 Volume 11, 2004 Volume 10, 2003 Volume 9, 2002 Volume 8, 2001 Volume 7, 2000 Volume 6, 1999 Volume 5, 1998 Volume 4, 1997 Volume 3, 1996 Volume 2, 1995 Volume 1, 1994

Journal of Enhanced Heat Transfer

DOI: 10.1615/JEnhHeatTransf.v24.i1-6.190
pages 269-278

BOILING HEAT TRANSFER FROM A SILICON CHIP IMMERSED IN DEGASSED AND GAS-DISSOLVED FC-72: EFFECTED BY SIZE AND NUMBER DENSITY OF MICRO-REENTRANT CAVITIES

H. Kubo
Interdisciplinary Graduate School of Engineering Sciences, Kyushu University, Kasuga, Fukuoka 816-8580, Japan
Hiroshi Takamatsu
Department of Mechanical Engineering, Kyushu University, Fukuoka 819-0395, Japan
Hiroshi Honda
Institute of Advanced Material Study, Kyushu University, Kasuga, Fukuoka 816-8580, Japan

RÉSUMÉ

Boiling heat transfer of FC-72 from newly developed treated surfaces with micro-reentrant cavities was studied experimentally. The surface structure was fabricated on a silicon chip by use of microelectronic fabrication techniques. Four kinds of treated surfaces with the combinations of two cavity mouth diameters (about 1.6 μm and 3.1 μm) and two number densities of the micro-reentrant cavities (81 l/cm2 and 96 × 103 l/cm2) were tested along with a smooth surface. Experiments were conducted at the liquid subcoolings of 3 K and 25 K with degassed and gas-dissolved FC-72. While the wall superheat at boiling incipience was strongly dependent on the dissolved gas content; it was little affected by the cavity mouth diameter and the liquid subcooling. The heat transfer performance of the treated surface was considerably higher than that of the smooth surface. The highest performance was obtained with a treated surface with a larger cavity mouth diameter and a larger cavity number density. The results were compared with those for previously developed treated surfaces.


Articles with similar content:

Effects of Size and Number Density of Micro-reentrant Cavities on Boiling Heat Transfer from a Silicon Chip Immersed in Degassed and Gas-dissolved FC-72
Journal of Enhanced Heat Transfer, Vol.6, 1999, issue 2-4
Hiroshi Takamatsu, Hiroshi Honda, H. Kubo
Enhanced Boiling Heat Transfer from Silicon Chips with Micro-Pin Fins Immersed in FC-72
Journal of Enhanced Heat Transfer, Vol.10, 2003, issue 2
Hiroshi Takamatsu, Hiroshi Honda, Jin Jia Wei
Effect of the size of micro-pin-fin on boiling heat transfer from silicon chips immersed in FC-72
International Heat Transfer Conference 12, Vol.46, 2002, issue
Hiroshi Takamatsu, Hiroshi Honda, Jin Jia Wei
EXPERIMENTAL STUDY OF POOL BOILING ON PIN-FINNED AND STRAIGHT-FINNED SURFACES ON AN INCLINED PLATE IN FC-72
Journal of Enhanced Heat Transfer, Vol.18, 2011, issue 4
Liang-Han Chien, Shu-Che Lee
Critical heat flux of R134a boiling flow in the circumferentially non-uniformly heated helically coiled tubes
International Heat Transfer Conference 16, Vol.18, 2018, issue
Huaijie Yuan, Xiaojuan Niu, Liang Zhao, Chen Quan