Abonnement à la biblothèque: Guest
Portail numérique Bibliothèque numérique eBooks Revues Références et comptes rendus Collections
Atomization and Sprays
Facteur d'impact: 1.189 Facteur d'impact sur 5 ans: 1.596 SJR: 0.814 SNIP: 1.18 CiteScore™: 1.6

ISSN Imprimer: 1044-5110
ISSN En ligne: 1936-2684

Volumes:
Volume 29, 2019 Volume 28, 2018 Volume 27, 2017 Volume 26, 2016 Volume 25, 2015 Volume 24, 2014 Volume 23, 2013 Volume 22, 2012 Volume 21, 2011 Volume 20, 2010 Volume 19, 2009 Volume 18, 2008 Volume 17, 2007 Volume 16, 2006 Volume 15, 2005 Volume 14, 2004 Volume 13, 2003 Volume 12, 2002 Volume 11, 2001 Volume 10, 2000 Volume 9, 1999 Volume 8, 1998 Volume 7, 1997 Volume 6, 1996 Volume 5, 1995 Volume 4, 1994 Volume 3, 1993 Volume 2, 1992 Volume 1, 1991

Atomization and Sprays

DOI: 10.1615/AtomizSpr.2013006939
pages 343-361

THREE-DIMENSIONAL INVESTIGATIONS OF FLOW CHARACTERISTICS IN A DIESEL NOZZLE

Weidi Huang
School of Automotive Studies, Tongji University, Shanghai 200092, China
Ya Gao
School of Automotive Studies, Tongji University, Shanghai 200092, China
Zhilong Li
School of Automotive Studies, Tongji University, Shanghai 200092, China
Liguang Li
School of Automotive Studies, Tongji University, Shanghai, 201804, People's Republic of China
Zhengbai Liu
Dongfeng Motor Corporation, Wuhan 430056, China
Zhijun Wu
School of Automotive Studies, Tongji University, Shanghai 200092, China

RÉSUMÉ

Simulation investigations of flow characteristic in diesel nozzles are basically performed using the simplified and idealized geometry models. Therefore, these simulations are essentially two-dimensional (2D), and unavoidably have deviations from real flow characteristics due to lack of three-dimensional (3D) geometry information. In this study, based on the high energy x-ray CT scan, the inner nozzle structures are measured in detail, and the measurement results are applied to generate the 3D computational meshes. The results of the 2D and the 3D simulations are compared to see the effect of the 3D simulation on the flow characteristics in the nozzles. The investigation results show that because of the rough surface and uneven distributions of geometry parameters in the azimuthal direction of the nozzle orifice revealed by the CT scan, the differences of the flow characteristics between the 2D and the 3D simulations are obvious. They exist at the orifice inlet, the orifice outlet, and along the orifice axis. The improvement of evenness of geometry parameter distributions can reduce the differences between the 2D and the 3D simulations. The 3D computational mesh, which contains more geometry parameter information than the 2D one, can reveal details of the influences of geometry parameters on the internal flow of nozzle, and gain more precise simulation results and insight into the flow characteristics under the real nozzle conditions.


Articles with similar content:

ENGINE COMBUSTION NETWORK (ECN): MEASUREMENTS OF NOZZLE GEOMETRY AND HYDRAULIC BEHAVIOR
Atomization and Sprays, Vol.22, 2012, issue 12
Tim Bazyn, Raul Payri, Alan L. Kastengren, Lyle M. Pickett, Julien Manin, Christopher F. Powell, F. Zak Tilocco

EXPERIMENTAL INVESTIGATION OF NEAR NOZZLE SPRAY STRUCTURE AND VELOCITY FOR A GDI HOLLOWCONE SPRAY
Atomization and Sprays, Vol.20, 2010, issue 12
D. Martin, Reinhold Kneer, Philipp Pischke, M. Cardenas

A CFD ANALYSIS OF THE INFLUENCE OF DIESEL NOZZLE GEOMETRY ON THE INCEPTION OF CAVITATION
Atomization and Sprays, Vol.13, 2003, issue 5&6
F. J. Salvador, Raul Payri, Xandra Margot, V. Macian

EMBEDDED DNS CONCEPT FOR SIMULATING THE PRIMARY BREAKUP OF AN AIRBLAST ATOMIZER
Atomization and Sprays, Vol.26, 2016, issue 3
Johannes Janicka, Amsini Sadiki, Benjamin Sauer

Characterization of Cavitation Flow in a Simple Hole Nozzle
International Journal of Fluid Mechanics Research, Vol.24, 1997, issue 1-3
Keiya Nishida, Steven L. Ceccio, Hiroyuki Hiroyasu, Dennis N. Assanis, N. Tamaki