Abonnement à la biblothèque: Guest
Portail numérique Bibliothèque numérique eBooks Revues Références et comptes rendus Collections
Atomization and Sprays
Facteur d'impact: 1.262 Facteur d'impact sur 5 ans: 1.518 SJR: 0.814 SNIP: 1.18 CiteScore™: 1.6

ISSN Imprimer: 1044-5110
ISSN En ligne: 1936-2684

Volumes:
Volume 29, 2019 Volume 28, 2018 Volume 27, 2017 Volume 26, 2016 Volume 25, 2015 Volume 24, 2014 Volume 23, 2013 Volume 22, 2012 Volume 21, 2011 Volume 20, 2010 Volume 19, 2009 Volume 18, 2008 Volume 17, 2007 Volume 16, 2006 Volume 15, 2005 Volume 14, 2004 Volume 13, 2003 Volume 12, 2002 Volume 11, 2001 Volume 10, 2000 Volume 9, 1999 Volume 8, 1998 Volume 7, 1997 Volume 6, 1996 Volume 5, 1995 Volume 4, 1994 Volume 3, 1993 Volume 2, 1992 Volume 1, 1991

Atomization and Sprays

DOI: 10.1615/AtomizSpr.v14.i4.40
22 pages

CHARACTERISTICS OF SPRAYS THROUGH A WALL IMPINGEMENT INJECTOR

Takao Inamura
Department of Intelligent Machines and Engineering, Hirosaki University, 3 Bunkyo-cho Hirosaki, 0368561, Japan
Terutoshi Tomoda
Engine Engineering Dev. 2, Toyota Motor Corporation, Susono-shi, Shizuoka-ken, Japan 410-1193

RÉSUMÉ

The behavior of a liquid film generated by the impingement of a liquid jet onto a solid wall was investigated for the purpose of its application to the design of an injector equipped with a direct-injection spark-ignition (DISI) engine. The liquid nozzle newly developed by the authors generates little turbulence in a liquid flow. The characteristics of a liquid film issuing from the edge of a solid wall (such as film spread angle and spray tip penetration) were measured by varying the injection conditions. The fuel injector was developed based on these basic experiments. The size of spray droplets injected through this injector was measured using a phase Doppler particle analyzer (PDPA), and the results were compared with those from the conventional slit-type injector. At the center of the spray, the droplet size distribution peaks at the small droplet diameter. At the periphery, this distribution peaks at a larger droplet diameter than at the center, but the distribution becomes narrower. The mean droplet size decreases gradually toward the periphery and then increases in size. The Sauter mean diameter of the spray injected through the newly developed injector ranges from 17 to 27 μm. The wall impingement-type injector has the potential to control the spray configuration by the impingement conditions and the shape of the wall surface.


Articles with similar content:

EXPERIMENTAL INVESTIGATION OF SPRAY CHARACTERISTICS OF DIESEL-METHANOL-WATER EMULSION
Atomization and Sprays, Vol.25, 2015, issue 8
Wuqiang Wang, Shenteng Cao, Dongyin Wu, Junjie Yan, Zhenzhou Pang
EFFECT OF ATOMIZING AIR FLOW ON SPRAY ATOMIZATION OF AN INTERNAL-MIX TWIN-FLUID ATOMIZER
Atomization and Sprays, Vol.25, 2015, issue 8
Cheng Tung Chong, Simone Hochgreb
A STUDY OF THE FLOW AND ATOMIZATION CHARACTERISTICS OF IMPINGED DIESEL SPRAY ON A CHAMBER WALL
Atomization and Sprays, Vol.17, 2007, issue 7
Chang Sik Lee, Sungwook Park, Hyun Kyu Suh
TIME-RESOLVED CHARACTERIZATION OF LOW-PRESSURE PULSED INJECTOR
Atomization and Sprays, Vol.26, 2016, issue 8
Pramod S. Mehta, Rohit Singh Pathania, Satyanarayanan R. Chakravarthy
EFFECTS OF IMPINGEMENT CONDITIONS ON THE CHARACTERISTICS OF MUTUAL IMPINGING SPRAY
Atomization and Sprays, Vol.17, 2007, issue 2
Gwon Hyun Ko, Hong Sun Ryou