Abonnement à la biblothèque: Guest
Portail numérique Bibliothèque numérique eBooks Revues Références et comptes rendus Collections
Atomization and Sprays
Facteur d'impact: 1.262 Facteur d'impact sur 5 ans: 1.518 SJR: 0.814 SNIP: 1.18 CiteScore™: 1.6

ISSN Imprimer: 1044-5110
ISSN En ligne: 1936-2684

Volumes:
Volume 29, 2019 Volume 28, 2018 Volume 27, 2017 Volume 26, 2016 Volume 25, 2015 Volume 24, 2014 Volume 23, 2013 Volume 22, 2012 Volume 21, 2011 Volume 20, 2010 Volume 19, 2009 Volume 18, 2008 Volume 17, 2007 Volume 16, 2006 Volume 15, 2005 Volume 14, 2004 Volume 13, 2003 Volume 12, 2002 Volume 11, 2001 Volume 10, 2000 Volume 9, 1999 Volume 8, 1998 Volume 7, 1997 Volume 6, 1996 Volume 5, 1995 Volume 4, 1994 Volume 3, 1993 Volume 2, 1992 Volume 1, 1991

Atomization and Sprays

DOI: 10.1615/AtomizSpr.2012003630
pages 1-21

EFFECT OF NOZZLE HOLE GEOMETRY ON NON-EVAPORATING DIESEL SPRAY CHARACTERISTICS AT HIGH-PRESSURE INJECTION

Jangsik Kong
Department of Mechanical Engineering, KAIST, 335 Gwahangno, Yuseong-gu, Daejon, 305-701, Republic of Korea
Choongsik Bae
Department of Mechanical Engineering, Korea Advanced Institute of Science and Technology, 373-1, Gusong-dong, Yuseong-gu, Daejon, 305-701, Republic of Korea

RÉSUMÉ

Non-evaporating diesel sprays from a common-rail injection system were characterized to investigate the effect of nozzle hole geometry. Two valve covered orifice (VCO) injectors with cylindrical and tapered nozzle holes were used. The injection rate was measured using an injection rate meter via the Bosch tube method. The spray tip penetration was analyzed from macroscopic spray images in a constant volume chamber using a high-resolution charge-coupled device camera and a spark light. Spray characteristics near the nozzle hole exit were observed using a microscopic visualization technique. The velocity and size of the droplets were measured downstream using a phase Doppler anemometer system. At the initial stage, the slope of the injection velocity from the tapered nozzle hole was larger than that from the cylindrical nozzle hole at the same injection pressure. The maximum injection velocity from the tapered nozzle hole was also higher. Until the micro-spray cone angle reached a maximum value, the spray tip penetration of the two nozzles increased with the change of injection rate. Subsequently, the spray tip penetration increased linearly with time. At the initial stage, the length of the liquid column injected from the tapered nozzle hole was about twice as long as that from the cylindrical nozzle hole. During the injection period, the oscillation in the micro-spray angle of the tapered nozzle hole was smaller than that of the cylindrical nozzle hole. The velocity and size of a droplet downstream with the tapered nozzle hole were slower and smaller than the velocity and size of the cylindrical nozzle hole.


Articles with similar content:

EFFECT OF SPLIT INJECTION ON THE MACROSCOPIC DEVELOPMENT AND ATOMIZATION CHARACTERISTICS OF A DIESEL SPRAY INJECTED THROUGH A COMMON-RAIL SYSTEM
Atomization and Sprays, Vol.16, 2006, issue 5
Rolf D. Reitz, Chang Sik Lee, Sungwook Park
DROPLET SIZE AND VELOCITY MEASUREMENTS IN A CRYOGENIC JET FLAME OF A ROCKET-TYPE COMBUSTOR USING HIGH-SPEED IMAGING
Atomization and Sprays, Vol.26, 2016, issue 5
Yves Le Sant, Arnaud Ristori, Lucien Vingert, Nicolas Fdida
EXPERIMENTAL INVESTIGATION OF THE ATOMIZATION CHARACTERISTICS OF ANTICORROSION WAX
Atomization and Sprays, Vol.23, 2013, issue 7
Sanghoon Lee, Sungwook Park
GAS ENTRAINMENT CHARACTERISTICS OF DIESEL SPRAY DURING END OF INJECTION TRANSIENT
Atomization and Sprays, Vol.19, 2009, issue 11
Keiya Nishida, Yuhei Matsumoto, Jeekuen Lee, Seoksu Moon
IMPINGEMENT OF HIGH-PRESSURE GASOLINE SPRAYS ON ANGLED SURFACES
Atomization and Sprays, Vol.16, 2006, issue 6
Jim H. Whitelaw, J. M. Nouri