Abonnement à la biblothèque: Guest
Portail numérique Bibliothèque numérique eBooks Revues Références et comptes rendus Collections
Atomization and Sprays
Facteur d'impact: 1.262 Facteur d'impact sur 5 ans: 1.518 SJR: 0.814 SNIP: 1.18 CiteScore™: 1.6

ISSN Imprimer: 1044-5110
ISSN En ligne: 1936-2684

Volumes:
Volume 29, 2019 Volume 28, 2018 Volume 27, 2017 Volume 26, 2016 Volume 25, 2015 Volume 24, 2014 Volume 23, 2013 Volume 22, 2012 Volume 21, 2011 Volume 20, 2010 Volume 19, 2009 Volume 18, 2008 Volume 17, 2007 Volume 16, 2006 Volume 15, 2005 Volume 14, 2004 Volume 13, 2003 Volume 12, 2002 Volume 11, 2001 Volume 10, 2000 Volume 9, 1999 Volume 8, 1998 Volume 7, 1997 Volume 6, 1996 Volume 5, 1995 Volume 4, 1994 Volume 3, 1993 Volume 2, 1992 Volume 1, 1991

Atomization and Sprays

DOI: 10.1615/AtomizSpr.v20.i2.50
pages 163-175

EFFECT OF AMBIENT TEMPERATURE AND DENSITY ON SHOCK WAVE GENERATION IN A DIESEL ENGINE

Sanghoon Kook
The University of New South Wales
Lyle M. Pickett
Combustion Research Facility, Sandia National Laboratories, P.O. Box 696, Livermore, CA 94551

RÉSUMÉ

Shock-wave generation by high-pressure diesel sprays has been investigated over a range of ambient temperature and density in a high-temperature, high-pressure optical vessel. In the past, shock wave generation was considered unlikely for diesel sprays because of the high-temperature environment and low fuel injection pressure. However, recent trends toward very high injection pressures, and earlier (lower temperature) injection in modern diesel engines, can potentially produce shock waves. Through high-speed schlieren imaging, injection-resolved shock waves have been captured at injection pressures of 150 MPa. Marked changes in shock wave generation are shown to occur with variation in ambient conditions that are experienced in an engine, including the following: (1) Shock waves diminish in strength with increasing temperature and eventually disappear due to the increasing speed of sound. (2) At low ambient temperature, high-density ambient gas quickly decelerates the tip of the spray, causing shock waves to detach from the spray. (3) At high ambient temperature, the high density decelerates the spray tip during injection-rate ramp-up before the spray reaches the speed of sound, such that no shock waves are produced.


Articles with similar content:

EXPERIMENTAL STUDY ON SPRAY CHARACTERISTICS OF EMULSIFIED DIESEL BLENDING WITH WATER IN A CONSTANT VOLUME CHAMBER
Atomization and Sprays, Vol.26, 2016, issue 6
Jie Tang, Sheng Huang, Zhaowen Wang, David Vuilleumier, Xiong Chen
EFFECT OF ELASTICITY OF BOGER FLUIDS ON THE ATOMIZATION BEHAVIOR OF AN IMPINGING JET INJECTOR
Atomization and Sprays, Vol.25, 2015, issue 8
Michele Negri, Helmut K. Ciezki
Dynamics of Circular Liquid Jet at Supercritical Chamber Conditions
Proceedings of the 24th National and 2nd International ISHMT-ASTFE Heat and Mass Transfer Conference (IHMTC-2017), Vol.0, 2017, issue
Aravind Vaidyanathan, Nandakumar K, C K Muthukumaran, Dhanesh A
EXPERIMENTAL CHARACTERIZATION OF SHEAR COAXIAL INJECTORS USING LIQUID/GASEOUS NITROGEN
Atomization and Sprays, Vol.7, 1997, issue 5
M. J. Glogowski, C. Puissant
EFFECT OF LINEAR ALKANE C17, C18 ON SPRAY CHARACTERISTICS OF KEROSENE IN HOLLOW CONE PRESSURE SWIRL SPRAY
Atomization and Sprays, Vol.27, 2017, issue 6
Haitao Ren, Xiaoyi Yang, Zhiwen Gan