Abonnement à la biblothèque: Guest
Portail numérique Bibliothèque numérique eBooks Revues Références et comptes rendus Collections
Atomization and Sprays
Facteur d'impact: 1.262 Facteur d'impact sur 5 ans: 1.518 SJR: 0.814 SNIP: 1.18 CiteScore™: 1.6

ISSN Imprimer: 1044-5110
ISSN En ligne: 1936-2684

Volumes:
Volume 29, 2019 Volume 28, 2018 Volume 27, 2017 Volume 26, 2016 Volume 25, 2015 Volume 24, 2014 Volume 23, 2013 Volume 22, 2012 Volume 21, 2011 Volume 20, 2010 Volume 19, 2009 Volume 18, 2008 Volume 17, 2007 Volume 16, 2006 Volume 15, 2005 Volume 14, 2004 Volume 13, 2003 Volume 12, 2002 Volume 11, 2001 Volume 10, 2000 Volume 9, 1999 Volume 8, 1998 Volume 7, 1997 Volume 6, 1996 Volume 5, 1995 Volume 4, 1994 Volume 3, 1993 Volume 2, 1992 Volume 1, 1991

Atomization and Sprays

DOI: 10.1615/AtomizSpr.v14.i3.10
20 pages

EXPERIMENTAL INVESTIGATION OF WATER MIST COOLING FOR GLASS TEMPERING

Nedim Sozbir
Mechanical Engineering Department, Carnegie Mellon University, Pittsburgh, Pennsylvania, USA
Shi-Chune Yao
Department of Mechanical Engineering, Institute for Complex Engineered Systems, Carnegie Mellon University, 5000 Forbes Avenue, Pittsburgh, PA, USA

RÉSUMÉ

High-velocity air jet impingement has been applied during the cooling process of glass tempering. In order to reduce the usage of high-pressure air in the process, it is intended to demonstrate the feasibility of using water mist to enhance the air cooling. The multiple jet experiments were performed using air jet velocities between 40 and 90 m/s containing low mass flux of water mist that was varied from 0 up to 0.145 kg/m2 s for each jet. The experiments include different glass thicknesses. The optimal tempering conditions were explored.
The mechanisms of mist cooling are revealed from the experiments of a single water mist jet impinging on hot stainless steel plates. Since the droplets are small, of the order of 22 μm, heat transfer distribution of the water mist has a similar form as the air jet cooling. The total heat transfer coefficient can be viewed as two separable effects: the summation of the heat transfer coefficient of the convective air and of the impinging water flux, respectively. The heat transfer of multiple water mist jets on larger glass is studied. The mist cooling demonstrates a define saving in the use of high-pressure air. When using mist cooling, the energy requirements of the system are significantly lowered. The mist cooling creates more refined fracturing in the punching tests of tempered glass. For glass thicker than 3 mm, the particle counts due to water mist improve about 121%. The improvement is about 38% for 2-mm glass. The test results indicate that thin and low-cost tempered glass can be made by mist cooling without fracture and with about 29% air pressure reduction for 2-mm glass plate and 50% reduction for both 3-mm and 4-mm glass plates.


Articles with similar content:

DEVELOPMENT OF HIGH PERFORMANCE AIR COOLING HEAT SINK UTILIZING PIN-FINS
International Heat Transfer Conference 10, Vol.22, 1994, issue
Ko Minakami, Masaru Ishizuka, Sadanari Mochizuki
EXPERIMENTAL STUDY OF NATURAL-CONVECTION COOLING OF DISCRETE HEATERS ON A PLATE IN RECTANGULAR ENCLOSURE
International Heat Transfer Conference 9, Vol.2, 1990, issue
Cha'o-Kuang Chen, C. J. Ho, Y. H. Hsu
Experimental investigation of a micro jets - based cooling package for electronic applications
International Heat Transfer Conference 12, Vol.46, 2002, issue
Matteo Fabbri , S. Jiang, Vijay K. Dhir
EFFECT OF LOCATIONS OF THE SUPPLY VENT ON THE EFFICIENCY INDEX OF A CONTAINER DATACENTER
Second Thermal and Fluids Engineering Conference, Vol.1, 2017, issue
Chi-Chuan Wang, Cheng-Hao Wang, Yeng-Yung Tsui
Development of All aluminum microchannel heat exchanger for air-conditioner
International Heat Transfer Conference 15, Vol.4, 2014, issue
Hirokazu Fujino, Satoshi Inoue, Toshimitsu Kamada