Abonnement à la biblothèque: Guest
Portail numérique Bibliothèque numérique eBooks Revues Références et comptes rendus Collections
Atomization and Sprays
Facteur d'impact: 1.262 Facteur d'impact sur 5 ans: 1.518 SJR: 0.814 SNIP: 1.18 CiteScore™: 1.6

ISSN Imprimer: 1044-5110
ISSN En ligne: 1936-2684

Volumes:
Volume 29, 2019 Volume 28, 2018 Volume 27, 2017 Volume 26, 2016 Volume 25, 2015 Volume 24, 2014 Volume 23, 2013 Volume 22, 2012 Volume 21, 2011 Volume 20, 2010 Volume 19, 2009 Volume 18, 2008 Volume 17, 2007 Volume 16, 2006 Volume 15, 2005 Volume 14, 2004 Volume 13, 2003 Volume 12, 2002 Volume 11, 2001 Volume 10, 2000 Volume 9, 1999 Volume 8, 1998 Volume 7, 1997 Volume 6, 1996 Volume 5, 1995 Volume 4, 1994 Volume 3, 1993 Volume 2, 1992 Volume 1, 1991

Atomization and Sprays

DOI: 10.1615/AtomizSpr.2015013725
pages 1151-1175

EFFECTS OF SPRAY PATTERNS ON THE MIXTURE FORMATION PROCESS IN MULTI-HOLE-TYPE DIRECT INJECTION SPARK IGNITION (DISI) GASOLINE ENGINES

Taehoon Kim
Department of Mechanical Convergence Engineering, Graduate School of Hanyang University, Seoul 133791, Republic of Korea; Department of Mechanical Science and Engineering University of Illinois at Urbana-Champaign MEB, 1206 W. Green St. Urbana, IL 61801, USA
Sungwook Park
School of Mechanical Engineering, Hanyang University, Seoul 133791, Republic of Korea

RÉSUMÉ

The direct injection concept is a prominent issue in spark ignition engines owing to direct injection's high fuel efficiency. However, proper fuel−air mixing technology is necessary to restrict exhaust emissions. Mixture preparation requires an understanding of the complex phenomena and physics regarding direct injection spark ignition (DISI) gasoline engines. Multihole-type DISI gasoline injectors can be used to generate various spray patterns. In this study, five types of spray patterns were considered for mixture preparation simulation: reference-type, circle-type, triangle-type, T-type, and Y-type patterns. Mass flow rate and initial droplet size were assumed to be the same for each nozzle. Also, cavitation for each nozzle was considered to be equal. Numerical analysis was carried out for wide open throttle conditions with a fixed engine speed (1500 rpm). Injection timing was set to BTDC 360 degrees, BTDC 315 degrees, and BTDC 270 degrees. The spray model and motoring pressure were validated before mixture preparation analysis. The BTDC 360 degree injection case was characterized by instant vaporization, whereas the BTDC 315 degree injection case was characterized by a fuel injection−dominant case, and the BTDC 270 degree injection case was characterized by a spray−flow interaction-dominant case. T-type and Y-type spray patterns showed faster evaporation than reference-type, circle-type, and triangle-type spray patterns.


Articles with similar content:

AN EXPERIMENT STUDY ON PHENOMENON AND MECHANISM OF FLASH BOILING SPRAY FROM A MULTI-HOLE GASOLINE DIRECT INJECTOR
Atomization and Sprays, Vol.23, 2013, issue 5
Shenghua Yang, Zhiping Song, Zhuo Yao, Tianyou Wang
EVAPORATING SPRAY SIMULATION IN A DIRECT INJECTION MODEL ENGINE
International Heat Transfer Conference 10, Vol.19, 1994, issue
Hong Sun Ryou, H.C. Yang, Young Ki Choi
ESTIMATE OF THE SUBGRID VARIANCE OF THE MIXTURE FRACTION IN SPRAY TURBULENT COMBUSTION
ICHMT DIGITAL LIBRARY ONLINE, Vol.13, 2008, issue
Hicham Meftah, Zakaria Bouali, Francois-Xavier Demoulin, Ahmed Mir, Julien Reveillon
EVALUATION OF SPRAY EVOLUTION IN PHARMACEUTICAL TABLET COATING PROCESSES: THE EFFECTS OF DRUM ROTATIONAL SPEED AND DRYING AIR FLOW RATE ON SPRAYS' CHARACTERISTICS
Atomization and Sprays, Vol.22, 2012, issue 9
Paul E. Sojka, Ariel R. Muliadi
EXPERIMENTAL STUDY ON LIQUID PHASE LPG SPRAY AND ICING PHENOMENON FOR A MIDDLE CLASS DIESEL ENGINE APPLICATION
Atomization and Sprays, Vol.21, 2011, issue 7
Ki-Hyung Lee, Ki-Bum Kim, Yung-Jin Kim