Abonnement à la biblothèque: Guest
Portail numérique Bibliothèque numérique eBooks Revues Références et comptes rendus Collections
Atomization and Sprays
Facteur d'impact: 1.262 Facteur d'impact sur 5 ans: 1.518 SJR: 0.814 SNIP: 1.18 CiteScore™: 1.6

ISSN Imprimer: 1044-5110
ISSN En ligne: 1936-2684

Volumes:
Volume 29, 2019 Volume 28, 2018 Volume 27, 2017 Volume 26, 2016 Volume 25, 2015 Volume 24, 2014 Volume 23, 2013 Volume 22, 2012 Volume 21, 2011 Volume 20, 2010 Volume 19, 2009 Volume 18, 2008 Volume 17, 2007 Volume 16, 2006 Volume 15, 2005 Volume 14, 2004 Volume 13, 2003 Volume 12, 2002 Volume 11, 2001 Volume 10, 2000 Volume 9, 1999 Volume 8, 1998 Volume 7, 1997 Volume 6, 1996 Volume 5, 1995 Volume 4, 1994 Volume 3, 1993 Volume 2, 1992 Volume 1, 1991

Atomization and Sprays

DOI: 10.1615/AtomizSpr.2019030077
pages 123-141

IN-NOZZLE CAVITATION AND DISCHARGED LIQUID JET DURING TRANSIENT INJECTION PROCESS

Rubby Prasetya
Graduate School of Maritime Sciences, Kobe University, Japan
Akira Sou
Graduate School of Maritime Sciences, Kobe University, Japan
Seoksu Moon
Department of Mechanical Engineering, Inha University
Raditya Hendra Pratama
Graduate School of Maritime Sciences, Kobe University, 5-1-1, Fukaeminami, Higashinada, Kobe 658-0022, Japan; Research Institute for Energy Conservation, National Institute of Advanced Industrial Science and Technology, Japan
Yoshitaka Wada
Powertrain Engineering Analysis Group, Mazda Motor Corporation, Japan
Hideaki Yokohata
Powertrain Engineering Analysis Group, Mazda Motor Corporation, Japan

RÉSUMÉ

Studies of internal flow and discharged liquid jets from the nozzle are sometimes carried out under steady injection conditions. Although steady injection data can be helpful for the study of internal flow in the nozzle, fuel injection is carried out under a transient injection scheme, which gives in-nozzle cavitation phenomena a transient characteristic. This difference raises some questions regarding the applicability of steady injection data to the transient injection process. In this study, high-speed visualization of cavitation in a rectangular plain-orifice nozzle and discharged liquid jet was carried out under steady and transient injection conditions in order to examine the applicability of steady injection data to the transient injection process. The cavitation length and discharged liquid jet angle data from the transient injection is used to investigate transient cavitation development in the macro scale, while X-ray phase contrast imaging of in-nozzle cavitation was carried out to clarify the morphology of cavitation inception in the micro scale. From the study, we clarified the applicability of steady injection data to transient injection processes. Correlations obtained from steady injection data can be used to predict cavitation growth and the discharged liquid jet angle during the transient injection process where the duration of the flow rate increase is much longer than the time scale of flow development in the nozzle. High-speed X-ray phase contrast imaging revealed two kinds of heterogeneous nucleation processes of cavitation inception induced by bubble nuclei in the bulk flow or the nozzle wall surface. Both are governed by the turbulent flow structure in the nozzle.

RÉFÉRENCES

  1. Arcoumanis, C., Flora, H., Gavaises, M., Kampanis, N., and Horrocks, R., Investigation of Cavitation in a Vertical Multi-Hole Injector, SAE Tech. Paper No. 1999-01-0524, 1999.

  2. Battistoni, M., Duke, D., Swantek, A., Tilocco, Z., Powell, C., and Som, S., Effects of Noncondensable Gas on Cavitating Nozzle, Atomization Sprays, vol. 25, no. 6, pp. 453–483, 2015.

  3. Bergwerk,W., Flow Pattern in Diesel Nozzle Spray Holes, Proc. of the Institution of Mechanical Engineers, vol. 173, no. 1, pp. 655–660, 1959.

  4. Brennen, C.E., Cavitation and Bubble Dynamics, New York: Oxford University Press, pp. 47–50, 1995.

  5. Chaves, H., Knapp, M., Kubitzek, A., and Obermeier, F., Experimental Study of Cavitation in the Nozzle Hole of Diesel Injectors using Transparent Nozzles, SAE Tech. Paper No. 950290, 1995.

  6. Cloetens, P., Barrett, R., Baruchel, J., Guigay, J.-P., and Schlenker, M., Phase Objects in Synchrotron Radiation Hard X-Ray Imaging, J. Phys. D: Appl. Phys., vol. 29, pp. 133–146, 1996.

  7. Duke, D., Swantek, A., Tilcco, Z., Kastengren, A., Fezzaa, K., Neroorkar, K., Moulai, M., Powell, C., and Schmidt, D., X-Ray Imaging of Cavitation in Diesel Injectors, SAE Int. J. Eng., vol. 7, no. 2, pp. 1003–1015, 2014.

  8. Duke, D., Swantek, A., Kastengren, A., Fezzaa, K., and Powell, C., Recent Developments in X-Ray Diagnostics for Cavitation, SAE Int. J. Fuels Lubricants, vol. 8, no. 1, pp. 135–146, 2015.

  9. Duke, D., Kastengren, A., Swantek, A., Matusik, K., and Powell, C., X-Ray Fluorescence Measurements of Dissolved Gas and Cavitation, Experiments Fluids, vol. 57, no.10, 2016.

  10. He, Z., Guo, G., Tao, X., Zhong,W., Leng, X., and Wang, Q., Study of the Effect of Nozzle Hole Shape on Internal Flow and Spray Characteristics, Int. Commun. Heat Mass Transf., vol. 71, pp. 1–8, 2016.

  11. Hiroyasu, H. and Arai, M., Structures of Fuel Sprays in Diesel Engines, SAE Tech. Paper No. 900475, 1990.

  12. Hult, J., Simmank, P., Matlok, M., Mayer, S., Falgout, Z., and Linne, M., Interior Flow and Near-Nozzle Spray Development in a Marine-Engine Diesel Fuel Injector, Experiments Fluids, vol. 57, no. 4, 2016. DOI: 10.1007/s00348-016-2134-8

  13. Iben, U., Morozov, A., Winklhofer, E., and Wolf, F., Laser-Pulse Interferometry Applied to High-Pressure Fluid Flow in Micro Channels, Experiments Fluids, vol. 50, no. 3, pp. 597–611, 2011.

  14. Inagaki, R., Yamazaki, T., Haibara, T.,Mitani, S.,Matsumura, E., and Senda, J., Visualization of Cavitation inside Nozzle Hole and Injected Liquid Jet, SAE Technical Paper No. 2015-01-1908, 2015.

  15. Inoue, K., Oka, T., Suzuki, T., Yagi, N., Takeshita, K., Goto, S., and Ishikawa, T., Present Status of High Flux Beamline (BL40XU) at SPring-8, Nuclear Instruments Methods Phys. Res., Section A: Accelerators, Spectrometers, Detectors Assoc. Equip., vols. 467–468, pp. 674–677, 2001.

  16. Jeon, J. and Moon, S., Ambient Density Effects on Initial Flow Breakup and Droplet Size Distribution of Hollow-Cone Sprays from Outwardly-Opening GDI Injector, Fuel, vol. 211, pp. 572–581, 2018.

  17. Kastengren, A. and Powell, C., Synchrotron X-Ray Techniques for Fluid Dynamics, Experiments Fluids, vol. 55, no. 3, p. 1686, 2014. DOI: 10.1007/s00348-014-1686-8

  18. Mauger, C., Mees, L., Michard, M., and Lance, M., Shadowgraph, Schlieren and Interferometry in a 2D Cavitating Channel Flow, Experiments Fluids, vol. 53, no. 6, pp. 1895–1913, 2012.

  19. Mitroglou, N., Stamboliyski, V., Karathanassis, I.K., Nikas, K.S., and Gavaises, M., Cloud Cavitation Vortex Shedding inside an Injector Nozzle, Experimental Therm. Fluid Sci., vol. 84, pp. 179–189, 2017.

  20. Moon, S., Komada, K., Li, Z., Wang, J., Kimijima, T., Arima, T., and Maeda, Y, High-Speed X-Ray Imaging of In-Nozzle Cavitation and Emerging Jet Flow of Multi-Hole GDI Injector under Practical Operating Conditions, Proc. of ICLASS 2015, 13th International Conference on Liquid Atomization and Spray Systems, Tainan, Taiwan, 2015.

  21. Nikl,M., Scintillation Detectors for X-Rays, Measurement Sci. Technol., vol. 17, no. 4, pp. R37–R54, 2006.

  22. Nurick,W.H., Orifice Cavitation and Its Effect on Spray Mixing, J. Fluids Eng., vol. 98, no. 4, p. 681, 1976.

  23. Olbinado, M.P., Just, X., Gelet, J.-L., Lhuissier, P., Scheel, M., Vagovic, P., Sato, T., Graceffa, R., Schulz, J., Mancuso, A., Morse, J., and Rack, A., MHz Frame Rate Hard X-Ray Phase-Contrast Imaging using Synchrotron Radiation, Optics Express, vol. 25, no. 12, pp. 13857–13871, 2017.

  24. Park, S.H., Suh, H.K., and Lee, C.S., Effect of Cavitating Flow on the Flow and Fuel Atomization Characteristics of Biodiesel and Diesel Fuels, Energy Fuels, vol. 22, pp. 605–613, 2008.

  25. Prasetya, R., Kasahara, T., Kotani, K., Miwa, T., Sou, A., Moon, S., Wada, Y., Ueki, Y., and Yokohata, H., X-Ray Imaging and Measurement of Cavitation Flow in Fuel Injector Nozzles with Various Geometries, Proc. of 19th Annual Conference of ILASS-Asia, Jeju, South Korea, 2017.

  26. Pratama, R.H., Sou, A., Katsui, T., and Nishio, S., String Cavitation in a Fuel Injector, Atomization Sprays, vol. 27, no. 3, pp. 189–205, 2017.

  27. Riken, BL40XU Outline, accessed September 27, 2018, from http://www.spring8.or.jp/wkg/BL40XU/inst rument/lang-en/INS-0000000353/instrument summary view, 2018.

  28. Roth, H., Gavaises, M., and Arcoumanis, C., Cavitation Initiation, Its Development and Link with Flow Turbulence in Diesel Injector Nozzles, SAE Tech. Paper No. 2002-01-0214, 2002.

  29. Salditt, T., Giewekemeyer, K., Fuhse, C., Kruger, S.P., Tucoulou, R., and Cloetens, P., Projection Phase Contrast Microscopy with a Hard X-Ray Nanofocused Beam: Defocus and Contrast Transfer, Phys. Rev. B—Condensed Matter Mater. Phys., vol. 79, p. 184112, 2009. DOI: 10.1103/PhysRevB.79.184112

  30. Schmidt, D. and Corradini, M.L., The Internal Flow of Diesel Fuel Injector Nozzles: A Review, Int. J. Engine Res., vol. 2, no. 1, pp. 1–22, 2001.

  31. Snigirev, A., Snigireva, I., Kohn, V., Kuznetsov, S., and Schelokov, I., On the Possibilities of X-Ray Phase Contrast Microimaging by Coherent High-Energy Synchrotron Radiation, Rev. Sci. Instruments, vol. 66, no. 12, pp. 5486–5492, 1995.

  32. Soteriou, C., Andrews, R., and Smith, M., Direct Injection Diesel Sprays and the Effect of Cavitation and Hydraulic Flip on Atomization, SAE Tech. Paper no. 950080, 1995.

  33. Sou,A., Tomiyama, S., Hosokawa, S., Nigorikawa, S., and Tatsutoshi, M., Cavitation in a Two-Dimensional Nozzle and Liquid Jet Atomization, JSME Int. J. Series B: Fluids Therm. Eng., vol. 49, no. 4, pp. 1253– 1259, 2006.

  34. Sou, A., Hosokawa, S., and Tomiyama, A., Effects of Cavitation in a Nozzle on Liquid Jet Atomization, Int. J. Heat Mass Transf., vol. 50, nos. 17-18, pp. 3575–3582, 2007.

  35. Sou, A., Maulana, M., Hosokawa, S., and Tomiyama, A., Effects of Nozzle Geometry on Cavitation in Nozzles of Pressure Atomizers, J. Fluid Sci. Technol., vol. 3, no. 5, pp. 622–632, 2008.

  36. Sou, A., Hosokawa, S., and Tomiyama, A., Cavitation in Nozzles of Plain Orifice Atomizers with Various Length-to-Diameter Ratios, Atomization Sprays, vol. 20, no. 6, pp. 513–524, 2010.

  37. Sou, A. and Pratama, R.H., Effects of Asymmetric Inflow on Cavitation in Fuel Injector and Discharged Liquid Jet, Atomization Sprays, vol. 26, no. 9, pp. 939–959, 2016.

  38. Yan, Y. and Thorpe, R.B., Flow Regime Transitions due to Cavitation in the Flow through an Orifice, Int. J. Multiphase Flow, vol. 16, no. 6, pp. 1023–1045, 1990.

  39. Yoda, T., Reduction of Diesel Combustion Noise by Controlling Fuel Injection, Denso Tech. Rev., vol. 15, pp. 110–114, 2010 (in Japanese).


Articles with similar content:

X-RAY RADIOGRAPHY MEASUREMENTS OF CAVITATING NOZZLE FLOW
Atomization and Sprays, Vol.23, 2013, issue 9
Daniel Duke, Andrew B. Swantek, Alan L. Kastengren, Christopher F. Powell, F. Zak Tilocco
Spray Break-Up Process of Diesel Fuel Investigated Close to the Nozzle
International Journal of Fluid Mechanics Research, Vol.24, 1997, issue 1-3
Alfred Leipertz, K.-U. Munch, A. Fath
CHARACTERISTICS OF FREE SPRAY DEVELOPMENT, MIXTURE FORMATION, AND COMBUSTION UNDER HIGH-PRESSURE SPLIT INJECTION
Atomization and Sprays, Vol.28, 2018, issue 3
Youichi Ogata, Keiya Nishida, Hirotaka Yamakawa, Kang Yang
X-RAY PHASE CONTRAST IMAGING OF CAVITATION AND DISCHARGED LIQUID JET IN NOZZLES WITH VARIOUS SIZES
Atomization and Sprays, Vol.29, 2019, issue 1
Akira Sou, Yoshitaka Wada, Hideaki Yokohata, Rubby Prasetya, Seoksu Moon, Raditya Hendra Pratama
MODELLING OF CAVITATION FLOW IN A NOZZLE AND ITS EFFECT ON SPRAY DEVELOPMENT
International Heat Transfer Conference 13, Vol.0, 2006, issue
Morgan R. Heikal, Sergey Martynov, David Mason, Sergei S. Sazhin, Mikhael Gorokhovski