Abonnement à la biblothèque: Guest
Portail numérique Bibliothèque numérique eBooks Revues Références et comptes rendus Collections
Atomization and Sprays
Facteur d'impact: 1.189 Facteur d'impact sur 5 ans: 1.596 SJR: 0.814 SNIP: 1.18 CiteScore™: 1.6

ISSN Imprimer: 1044-5110
ISSN En ligne: 1936-2684

Volumes:
Volume 29, 2019 Volume 28, 2018 Volume 27, 2017 Volume 26, 2016 Volume 25, 2015 Volume 24, 2014 Volume 23, 2013 Volume 22, 2012 Volume 21, 2011 Volume 20, 2010 Volume 19, 2009 Volume 18, 2008 Volume 17, 2007 Volume 16, 2006 Volume 15, 2005 Volume 14, 2004 Volume 13, 2003 Volume 12, 2002 Volume 11, 2001 Volume 10, 2000 Volume 9, 1999 Volume 8, 1998 Volume 7, 1997 Volume 6, 1996 Volume 5, 1995 Volume 4, 1994 Volume 3, 1993 Volume 2, 1992 Volume 1, 1991

Atomization and Sprays

DOI: 10.1615/AtomizSpr.v19.i1.50
pages 75-90

THREE-DIMENSIONAL SIMULATION OF EFFERVESCENT ATOMIZATION SPRAY

Hong-Bing Xiong
Department of Mechanics, Zhejiang University, Hangzhou, 310027, China China Jiliang University, Hangzhou, 310018, China
Jianzhong Lin
Department of Mechanics, Zhejiang University, and Jiliang University, Hangzhou, China
Ze-Fei Zhu
Zhejiang Sci-Tech University, Hangzhou, 310018, China

RÉSUMÉ

A comprehensive three-dimensional model of droplet-gas two-phase flow is presented to examine the evolution of spray along the downstream of the exit orifice in an effervescent atomizer. For gas phase, the Navier-Stokes equations with k−ε turbulence model are solved, considering two-way coupling of the interaction between droplets and the gas phase. The dispersed droplet phase is modeled as Lagrangian entities, accounting for the physical phenomena of droplet generation from primary and secondary breakup, droplet collision and coalescence, droplet momentum, and heat transfer. This model is used to calculate the mean size and statistical distributions of atomized droplets under various operating conditions such as air-to-liquid ratio (ALR), injection pressure, liquid flow rate, nozzle exit diameter, and liquid material. The simulation results compare well with the experimental data, with an accuracy of 5% for the atomizer operated under annular flow conditions. Gas flow and spray evolution of the droplets are predicted; effects of operating conditions on the droplet mean size and distributions are discussed. Results show that ALR is one of the most important control parameters. Increasing ALR will decrease the droplet size gradually and finally tend to a certain limitation. A decreasing nozzle exit favors primary breakup, while high injection pressure has more influence on the secondary atomization. An increasing liquid mass flow rate has better primary breakup and worse overall atomization downstream. The liquid properties also have great impact on the droplet atomization. The less the viscosity and surface tension, the easier liquid breaks into smaller drops.


Articles with similar content:

NUMERICAL SIMULATION OF DROPLET FORMATION FROM COAXIAL TWIN-FLUID ATOMIZER
Atomization and Sprays, Vol.12, 2002, issue 1-3
Takao Inamura, Masatoshi Daikoku
Numerical Study on Heat Transfer Enhancement in a Mist/Air Impingement Jet
Journal of Enhanced Heat Transfer, Vol.17, 2010, issue 3
Mohammad Mahdi Heyhat, Hossein Shokouhmand
VACUUM-ASSISTED GAS ATOMIZATION OF LIQUID METAL
Atomization and Sprays, Vol.22, 2012, issue 7
F. S. Biancaniello, S. D. Ridder, Steven P. Mates, T. Zahrah
DEVELOPMENT AND ASSESSMENT OF A HYBRID DROPLET COLLISION MODEL FOR TWO IMPINGING SPRAYS
Atomization and Sprays, Vol.13, 2003, issue 2&3
Gwon Hyun Ko, Hong Sun Ryou, Young Ki Choi, Seong Hyuk Lee
MASS DISTRIBUTION STUDIES IN EFFERVESCENT SPRAYS
Atomization and Sprays, Vol.21, 2011, issue 5
Ali Dolatabadi, Hrishikesh Gadgil, B. N. Raghunandan