Abonnement à la biblothèque: Guest
Portail numérique Bibliothèque numérique eBooks Revues Références et comptes rendus Collections
Atomization and Sprays
Facteur d'impact: 1.189 Facteur d'impact sur 5 ans: 1.596 SJR: 0.814 SNIP: 1.18 CiteScore™: 1.6

ISSN Imprimer: 1044-5110
ISSN En ligne: 1936-2684

Volumes:
Volume 29, 2019 Volume 28, 2018 Volume 27, 2017 Volume 26, 2016 Volume 25, 2015 Volume 24, 2014 Volume 23, 2013 Volume 22, 2012 Volume 21, 2011 Volume 20, 2010 Volume 19, 2009 Volume 18, 2008 Volume 17, 2007 Volume 16, 2006 Volume 15, 2005 Volume 14, 2004 Volume 13, 2003 Volume 12, 2002 Volume 11, 2001 Volume 10, 2000 Volume 9, 1999 Volume 8, 1998 Volume 7, 1997 Volume 6, 1996 Volume 5, 1995 Volume 4, 1994 Volume 3, 1993 Volume 2, 1992 Volume 1, 1991

Atomization and Sprays

DOI: 10.1615/AtomizSpr.2014010224
pages 625-650

CHARACTERISTICS OF ADHESION DIESEL FUEL ON AN IMPINGEMENT DISK WALL. PART 3: AMBIENT PRESSURE EFFECT

Mohd Zaid Akop
Division of Mechanical Science and Technology, Faculty of Science and Technology, Gunma University, 1-5-1 Tenjin-cho, Kiryu, Gunma, 376-8515, Japan
Yoshio Zama
Division of Mechanical Science and Technology, Gunma University, 1-5-1 Tenjin-cho, Kiryu, Gunma, Japan, 376-8515
Tomohiko Furuhata
Division of Mechanical Science and Technology, Faculty of Science and Technology, Gunma University, 1-5-1 Tenjin-cho, Kiryu, Gunma, 376-8515, Japan
Masataka Arai
Division of Mechanical Science and Technology, Faculty of Science and Technology, Gunma University, 1-5-1 Tenjin-cho, Kiryu, Gunma, 376-8515, Japan; Tokyo Denki University

RÉSUMÉ

Wall impingement of fuel spray is known as the main contributor to DI diesel engines with small combustion cavities. Recently, high boost intake air charging has been adopted in the diesel engine for higher power and better performance including low emissions. Consequently, the compressed air density in the cylinder is becoming high, and it seems that this high density surrounding air has a greater effect on the impingement behavior of fuel sprays. Therefore, under high gas density conditions, precise investigation of impingement fuel sprays is needed. In this paper, the effect of ambient pressure and injection pressure on the adhered fuel mass of normal impingement diesel sprays was investigated experimentally. Nonevaporated diesel spray was injected into a high-pressure vessel, and the spray impinged to a flat wall was placed in the vessel. The ambient pressure in the vessel was set from 0.1 to 4 MPa. The mass of the disk with adhered fuel was measured using an electronic balance, and the fuel mass adhered on its surface was evaluated. As a result, it was found that the adhered mass ratio decreased with an increase of ambient pressures from 0.1 to 1 MPa. However, at ambient pressure over 1.0 MPa, the adhered mass ratio became almost constant for a condition of30 mm impingement distance but it still decreased under longer impingement distances such as 90 mm. Under long impingement distances, adhered fuel mass in high ambient pressure conditions such as 4 MPa was half of that under 1 MPa conditions. Moreover, the height of the impingement spray changed in various ways under various ambient pressures. It had partial correlation with adhered mass ratio. The result also shows that adhered mass was greatly affected by the Weber number which was obtained with impingement velocity and the Sauter mean diameter of the spray. Finally, the jet number was introduced to summarize the effects of ambient pressure and impingement Weber number on adhered mass ratio.


Articles with similar content:

CHARACTERISTICS OF ADHESION DIESEL FUEL ON AN IMPINGEMENT DISK WALL PART 2: DROPLET WEBER NUMBER AND ADHERED FUEL MASS
Atomization and Sprays, Vol.24, 2014, issue 8
Masataka Arai, Yoshio Zama, Tomohiko Furuhata, Mohd Zaid Akop
CHARACTERISTICS OF ADHESION OF DIESEL FUEL ON IMPINGEMENT DISK WALL. PART 1: EFFECT OF IMPINGEMENT AREA AND INCLINATION ANGLE OF DISK
Atomization and Sprays, Vol.23, 2013, issue 8
Masataka Arai, Yoshio Zama, Tomohiko Furuhata, Mohd Zaid Akop
DIESEL SPRAY IMPINGING ON A FLAT WALL, PART I: CHARACTERISTICS OF ADHERED FUEL FILM IN AN IMPINGEMENT DIESEL SPRAY
Atomization and Sprays, Vol.12, 2002, issue 5&6
Masataka Arai, Kyungnam Ko
DIESEL SPRAY BEHAVIOR AT COMPRESSION RATIOS UP TO 100:1
Atomization and Sprays, Vol.20, 2010, issue 5
S. L. Miller, Matt N. Svrcek, Christopher F. Edwards
A STUDY OF THE FLOW AND ATOMIZATION CHARACTERISTICS OF IMPINGED DIESEL SPRAY ON A CHAMBER WALL
Atomization and Sprays, Vol.17, 2007, issue 7
Chang Sik Lee, Sungwook Park, Hyun Kyu Suh