Abonnement à la biblothèque: Guest
Portail numérique Bibliothèque numérique eBooks Revues Références et comptes rendus Collections
Atomization and Sprays
Facteur d'impact: 1.262 Facteur d'impact sur 5 ans: 1.518 SJR: 0.814 SNIP: 1.18 CiteScore™: 1.6

ISSN Imprimer: 1044-5110
ISSN En ligne: 1936-2684

Volumes:
Volume 29, 2019 Volume 28, 2018 Volume 27, 2017 Volume 26, 2016 Volume 25, 2015 Volume 24, 2014 Volume 23, 2013 Volume 22, 2012 Volume 21, 2011 Volume 20, 2010 Volume 19, 2009 Volume 18, 2008 Volume 17, 2007 Volume 16, 2006 Volume 15, 2005 Volume 14, 2004 Volume 13, 2003 Volume 12, 2002 Volume 11, 2001 Volume 10, 2000 Volume 9, 1999 Volume 8, 1998 Volume 7, 1997 Volume 6, 1996 Volume 5, 1995 Volume 4, 1994 Volume 3, 1993 Volume 2, 1992 Volume 1, 1991

Atomization and Sprays

DOI: 10.1615/AtomizSpr.v17.i5.10
pages 381-407

EXPERIMENTAL STUDY OF COAXIAL ATOMIZERS SCALING. PART I: DENSE CORE ZONE

Bertrand Leroux
Air Liquide, Centre de Recherche Claude Delorme, Les Loges en Josas, BP 126, 78350 Jouy en Josas, France
Olivier Delabroy
Air Liquide, Centre de Recherche Claude Delorme, Les Loges en Josas, BP 126, 78350 Jouy en Josas, France
Francois Lacas
Laboratoire EM2C, C.N.R.S., Ecole Centrale Paris, Grande Voie des Vignes, 92295 Châtenay-Malabry, France

RÉSUMÉ

Coaxial injection is a very common system in industrial burners or rocket engines. Theoretical studies involving different hypotheses have been devoted to this subject. Experimental studies have been performed in several individual configurations. Subsequently, many correlations are proposed in the literature. All these expressions do not take into account the same basic quantities, which may be troublesome for injector designers. In the present work, we have performed experiments in a system where both geometry and liquid characteristics could be varied over a wide range. Changes in atomization regimes, liquid core length, and spray angle are especially examined in the present paper. They were estimated using fast shadowgraphy. We show that the momentum flux ratio plays a key role in all these quantities in the dense core zone. Gas flow Reynolds number is also important for disintegration mode classification. Empirical correlations show that liquid's physical properties (viscosity or surface tension) have little influence on the atomization process in the range studied. The Rayleigh instability growth rate model, based on the existence of a shear layer at the interface, seems to be the most suitable in predicting the dense core zone properties, showing that primary atomization in coaxial injectors is essentially ruled by aerodynamic effects.


Articles with similar content:

EXPERIMENTAL STUDY OF COAXIAL ATOMIZERS SCALING. PART II: DILUTED ZONE
Atomization and Sprays, Vol.17, 2007, issue 5
Francois Lacas, Bertrand Leroux, Olivier Delabroy
EFFECT OF SINGLE- AND MULTI-HOLE BUBBLE BREAKERS ON THE EFFERVESCENT ATOMIZATION PROCESS
Atomization and Sprays, Vol.26, 2016, issue 2
Aly H. Gadallah, Kamran Siddiqui, Mona Hassanzadeh Jobehdar, Wajid A. Chishty
INFLUENCE OF TWO-PHASE FEED BUBBLE SIZE ON EFFERVESCENT ATOMIZATION IN A HORIZONTAL NOZZLE ASSEMBLY
Atomization and Sprays, Vol.21, 2011, issue 3
Jason S. Olfert, Johana Gomez, Brian A. Fleck, J. McMillan
THE INTERNAL FLOW AND EXIT CONDITIONS OF PRESSURE SWIRL ATOMIZERS
Atomization and Sprays, Vol.10, 2000, issue 2
J. J. Chinn
Experimental Investigation of Polydisperse Spray Interaction
International Journal of Fluid Mechanics Research, Vol.24, 1997, issue 4-6
Günter Brenn, A. Selbach