Abonnement à la biblothèque: Guest
Portail numérique Bibliothèque numérique eBooks Revues Références et comptes rendus Collections
Atomization and Sprays
Facteur d'impact: 1.262 Facteur d'impact sur 5 ans: 1.518 SJR: 0.814 SNIP: 1.18 CiteScore™: 1.6

ISSN Imprimer: 1044-5110
ISSN En ligne: 1936-2684

Volumes:
Volume 29, 2019 Volume 28, 2018 Volume 27, 2017 Volume 26, 2016 Volume 25, 2015 Volume 24, 2014 Volume 23, 2013 Volume 22, 2012 Volume 21, 2011 Volume 20, 2010 Volume 19, 2009 Volume 18, 2008 Volume 17, 2007 Volume 16, 2006 Volume 15, 2005 Volume 14, 2004 Volume 13, 2003 Volume 12, 2002 Volume 11, 2001 Volume 10, 2000 Volume 9, 1999 Volume 8, 1998 Volume 7, 1997 Volume 6, 1996 Volume 5, 1995 Volume 4, 1994 Volume 3, 1993 Volume 2, 1992 Volume 1, 1991

Atomization and Sprays

DOI: 10.1615/AtomizSpr.v11.i3.10
pages 201-226

MEASUREMENT OF BREAKUP LENGTH OF CYLINDRICAL LIQUID JETS. APPLICATION TO LOW-PRESSURE CAR INJECTOR

Christophe Dumouchel
Université et INSA de Rouen France

RÉSUMÉ

The present article reports an experimental investigation on the characterization of the atomization of plain cylindrical liquid jets. The main objective of the work is to measure the stability curve of jets produced by two different injectors, one of them being dedicated to low-pressure fuel-port-injected engines. Furthermore, in order to investigate the influence of the liquid, three different liquids have been tested. The experimental technique used here was developed in a previous investigation and allows one to obtain jet breakup lengths averaged from 1000 measurements for each situation. The results are therefore regarded as very accurate and reliable. It is found that the stability curve of a liquid jet contains useful information as far as the atomization of the liquid system is concerned. Confirming results obtained in a previous study, it is found here that according to the fluid used, the jet produced by an injector can show different behavior that affects its breakup length as well as the sensitivity of this length to the ambient condition. In applications such as in low-pressure gasoline injection, such information may be very valuable for development of an injection strategy.


Articles with similar content:

ANALYSIS OF DIESEL SPRAY ATOMIZATION BY MEANS OF A NEAR-NOZZLE FIELD VISUALIZATION TECHNIQUE
Atomization and Sprays, Vol.21, 2011, issue 9
Jaime Gimeno, Raul Payri, Javier Salvador, J. De la Morena
LARGE EDDY SIMULATION OF SINGLE DROPLET AND LIQUID JET PRIMARY BREAKUP USING A COUPLED LEVEL SET/VOLUME OF FLUID METHOD
Atomization and Sprays, Vol.24, 2014, issue 4
James J. McGuirk, Feng Xiao, M. Dianat
EXPERIMENTAL STUDY OF COAXIAL ATOMIZERS SCALING. PART I: DENSE CORE ZONE
Atomization and Sprays, Vol.17, 2007, issue 5
Francois Lacas, Bertrand Leroux, Olivier Delabroy
ATOMIZATION CHARACTERISTICS OF PRESSURE-MODULATED AUTOMOTIVE PORT INJECTOR SPRAYS
Atomization and Sprays, Vol.6, 1996, issue 4
Fu-Quan Zhao, Amer Ahmad Amer, John L. Dressler
AN EXPERIMENTAL STUDY ON MICROSCOPIC CHARACTERISTICS OF FLASH BOILING SPRAY WITH EXTENDED GLARE POINT VELOCIMETRY AND SIZING
Atomization and Sprays, Vol.26, 2016, issue 5
Shenghua Yang, Ming Jia, Zhuo Yao, Shiquan Shen, Tianyou Wang