ライブラリ登録: Guest
Begell Digital Portal Begellデジタルライブラリー 電子書籍 ジャーナル 参考文献と会報 リサーチ集
Heat Transfer Research
インパクトファクター: 0.404 5年インパクトファクター: 0.8 SJR: 0.264 SNIP: 0.504 CiteScore™: 0.88

ISSN 印刷: 1064-2285
ISSN オンライン: 2162-6561

巻:
巻 50, 2019 巻 49, 2018 巻 48, 2017 巻 47, 2016 巻 46, 2015 巻 45, 2014 巻 44, 2013 巻 43, 2012 巻 42, 2011 巻 41, 2010 巻 40, 2009 巻 39, 2008 巻 38, 2007 巻 37, 2006 巻 36, 2005 巻 35, 2004 巻 34, 2003 巻 33, 2002 巻 32, 2001 巻 31, 2000 巻 30, 1999 巻 29, 1998 巻 28, 1997

Heat Transfer Research

DOI: 10.1615/HeatTransRes.2016012206
pages 753-765

TRANSIENT HEAT CONDUCTION IN WIRES WITH HEAT SOURCES; LUMPED AND DISTRIBUTED SOLUTION TECHNIQUES

Federico Scarpa
University of Genoa, DIME/TEC, Division of Thermal Energy and Environmental Conditioning Via All'Opera Pia 15 A, 16145 Genoa, Italy
Mattia De Rosa
University of Genoa, DIME/TEC, Division of Thermal Energy and Environmental Conditioning Via All'Opera Pia 15 A, 16145 Genoa, Italy

要約

The aim of this study is to test the approximate lumped analysis against the more rigorous distributed parameter approach in the solution of 1D and 2D nonlinear heat conduction problems associated with electrical cables under a current load. The system of partial differential equations governing the distributed parameter model is replaced by a system of ordinary differential equations with total derivatives with respect to time. The number of temperature unknowns is highly reduced and the numerical solution, even though approximate, can be very fast. Furthermore, with the use of the thermal-electrical analogy, the lumped system can be described as an equivalent electric circuit composed of thermal resistances and capacitances properly connected and solved with dedicated software. In this work, the lumped approach is applied to the overheating effect of insulated electric cables under a current load both in a steady and a transient regime. For this application, the lumped methodology can be very useful owing to the presence of several regions of solution domain having negligible internal conductive resistance. The approximate solutions are compared with the distributed parameter approach obtained with a commercial FEM code. An empirical methodology is described for modeling single cables and composite flat cables in such a way as to minimize the difference between the approximate and the more rigorous solution, both in a steady state and in a dynamic regime. The difference can be limited to less than few percent and can be considered fully adequate for industrial design.


Articles with similar content:

Thermal Management Characteristics of Lithium-ion Batteries According to the Arrangement
International Heat Transfer Conference 15, Vol.8, 2014, issue
Son Jong Hyeon, Park Il Seouk, Lee Heewon
NUMERICAL INVESTIGATION OF DUAL HIGH HEAT FLUX THERMAL MANAGEMENT FOR A PHASED ARRAY ANTENNA WITH MICROCHANNEL COOLING TECHNIQUES
3rd Thermal and Fluids Engineering Conference (TFEC), Vol.28, 2018, issue
E. Örs, M. Parlak, H. H Kılıç
OSCILLATORY HEAT TRANSFER IN EXTENDED SURFACES
International Heat Transfer Conference 9, Vol.4, 1990, issue
J. M. Houghton, Peter J. Heggs, Derek B. Ingham
SCENARIO FOR TRANSITION TO CHAOS THROUGH INTERMITTENCY IN AVALANCHE GENERATOR DIODES WITH AN EXTERNAL SIGNAL
Telecommunications and Radio Engineering, Vol.77, 2018, issue 5
P. P. Maksymov
Expanded Lumped Model for the Algebraic Evaluation of the Total Heat Rejection from a Large Plate Immersed in a Fluid during a Period of Time
Heat Transfer Research, Vol.40, 2009, issue 4
Antonio Campo, Luis E. Herranz