ライブラリ登録: Guest
Begell Digital Portal Begellデジタルライブラリー 電子書籍 ジャーナル 参考文献と会報 リサーチ集
Heat Transfer Research
インパクトファクター: 0.404 5年インパクトファクター: 0.8 SJR: 0.264 SNIP: 0.504 CiteScore™: 0.88

ISSN 印刷: 1064-2285
ISSN オンライン: 2162-6561

巻:
巻 51, 2020 巻 50, 2019 巻 49, 2018 巻 48, 2017 巻 47, 2016 巻 46, 2015 巻 45, 2014 巻 44, 2013 巻 43, 2012 巻 42, 2011 巻 41, 2010 巻 40, 2009 巻 39, 2008 巻 38, 2007 巻 37, 2006 巻 36, 2005 巻 35, 2004 巻 34, 2003 巻 33, 2002 巻 32, 2001 巻 31, 2000 巻 30, 1999 巻 29, 1998 巻 28, 1997

Heat Transfer Research

DOI: 10.1615/HeatTransRes.2018026458
pages 89-105

THERMOHYDRAULIC CHARACTERISTICS OF MICROCHANNEL HEAT SINKS COMBINED WITH RIBS AND CAVITIES: EFFECTS OF GEOMETRIC PARAMETERS AND HEAT FLUX

Cong Li
Department of Process Equipment and Control Engineering, School of Mechanical Engineering, Xiangtan University, Xiangtan 411105, People's Republic of China
Hong-Ju Guo
Department of Process Equipment and Control Engineering, School of Mechanical Engineering, Xiangtan University, Xiangtan 411105, People's Republic of China
Wei-Biao Ye
Department of Process Equipment and Control Engineering, School of Mechanical Engineering, Xiangtan University, Xiangtan 411105, People's Republic of China
Yuxiang Hong
Department of Chemistry and Chemical Engineering, Lishui University, Lishui 323000, People's Republic of China
Si-Min Huang
Key Laboratory of Distributed Energy Systems of Guangdong Province, Department of Energy and Chemical Engineering, Dongguan University of Technology, Dongguan 523808, People's Republic of China

要約

The effects of the geometric parameters and heat flux on the thermohydraulic characteristics of microchannel heat sinks combined with ribs and cavities are investigated numerically. The numerical study is performed under conditions of laminar flow with conjugate heat transfer between silicon and water. In order to find the optimum substrate thickness, ratios of substrate thickness to microchannel height (Hs/Hc = 0, 0.25, 0.50, 0.75, 1.00, 1.25, and 1.50) are investigated. It is found that the temperature of the substrate surface firstly decreases and then gradually increases, the minimum temperature of the substrate surface occurs with Hs/Hc = 0.25. Furthermore, the microchannel heat sinks are studied at rib width to the spacing ratios (Lr/Sr = 0.25, 0.50, 0.75, and 1.0), rib heights to parallel sidewalls width ratios (Hr/Wc = 0.10, 0.15, 0.20, and 0.25), spacing to the parallel sidewalls width ratios (Sr/Wc = 4, 8, 12, and 16) and heat fluxes (qw = 50, 100, 150, 200, 250, and 300 W cm–2). The results show that the Performance Evaluation Criterion (PEC) is continued to slowly decrease with increase of qw. For all cases of qw, the maximum value of PEC occurs in model 2 with Lr/Sr = 0.50, Hr/Wc = 0.20, and Sr/Wc = 4. For Re > 320, the wall temperature of model 1 is slightly smaller than that of model 2.


Articles with similar content:

Laminar forced convection in two-dimensional impacting tee junctions
International Heat Transfer Conference 12, Vol.13, 2002, issue
Scott J. Ormiston, A. M. F. El-Shaboury, Hassan M. Soliman
THEORETICAL AND EXPERIMENTAL INVESTIGATIONS OF MODIFICATION OF MATERIALS AT LOW PRESSURE RF PLASMAS
Progress in Plasma Processing of Materials, 2003, Vol.0, 2003, issue
A. Meckeshkin-Abdullin, Victor Jeltoukhine, I. A. Abdullin
ENHANCED HEAT TRANSFER OF FLOW BOILING COMBINED WITH JET IMPINGEMENT
Interfacial Phenomena and Heat Transfer, Vol.1, 2013, issue 1
Yonghai Zhang, Dong Guo, Jin-Jia Wei, Jian-Fu Zhao
EFFECTIVENESS OF SURFACE POLARITONS IN PERFORMANCE IMPROVEMENT OF THE NEAR-FIELD THERMOPHOTOVOLTAIC SYSTEM WITH A METAMATERIAL RADIATOR
Heat Transfer Research, Vol.50, 2019, issue 4
Qilin Cai, Xi Wu, Xiaojing Zhang, Peizhou Chen, Qichen Xu
INFLUENCE OF SPLITTER PLATE ARRANGEMENT ON FLOW PAST RECTANGULAR CYLINDERS OF DIFFERENT ASPECT RATIOS
Journal of Flow Visualization and Image Processing, Vol.12, 2005, issue 4
D. Pramod Kumar, S. Vengadesan