ライブラリ登録: Guest
Begell Digital Portal Begellデジタルライブラリー 電子書籍 ジャーナル 参考文献と会報 リサーチ集
Journal of Enhanced Heat Transfer
インパクトファクター: 0.562 5年インパクトファクター: 0.605 SJR: 0.175 SNIP: 0.361 CiteScore™: 0.33

ISSN 印刷: 1065-5131
ISSN オンライン: 1026-5511

Journal of Enhanced Heat Transfer

DOI: 10.1615/JEnhHeatTransf.2018018871
pages 499-512

STUDY AND OPTIMIZATION OF PARAMETERS THAT INFLUENCE THERMOHYDRAULIC PERFORMANCE OF FLOW IN A DUCT WITH TWISTED TAPE INSERT IN CONJUNCTION WITH DIMPLES OVER ITS SURFACE

P. S. Kishore
Department of Mechanical Engineering, College of Engineering, Andhra University, Visakhapatnam 530003, India
V. Koteswara Reddy
Department of Mechanical Engineering, Govt. Polytechnic, Vizianagaram, 535002, India
M. Prem Dheeraj
Department of Mechanical Engineering, Anil Neerukonda Institute of Technology & Science, Sangivalasa, Visakhapatnam 531162, India
K. Pavan Kumar
Department of Mechanical Engineering, Gayatri Vidhya Parishad Technical Campus, Rushikonda, Visakhapatnam 530045, India

要約

Transport of energy across fluids is facilitated within a device called a heat exchanger. The ability to exchange thermal energy within this device is further enhanced by applying various passive and active techniques. In this work, a group of passive techniques were merged to improve the performance of a heat exchanger. A square duct is considered to represent the tube of a heat exchanger as water flows inside the duct. A spiral insert is placed within a square duct and two opposite walls of the duct are dented to impinge hemispherical dimples. The effect of a spiral insert and dimples on heat exchanger performance was observed in ANSYS at various configurations of dimples by keeping the spiral insert unaltered. This study is further extended to analyze and predict the best dimple configuration using optimization techniques such as genetic algorithms (GAs) and microgenetic algorithms (μGAs). Using a GA, the best thermohydraulic performance is observed when spacing between the dimples is 7.5 mm, 5.5 mm, and 7.5 mm from the edge of the duct surface. The result suggested by a μGA is also in close agreement with the result of the GA. According to the μGA, the best thermohydraulic performance is predicted at 7.4 mm, 5.6 mm, and 7.4 mm from the edge of the duct surface.


Articles with similar content:

Development of a surface shape for the heat transfer enhancement and reduction of pressure loss in an internal cooling passage
TSFP DIGITAL LIBRARY ONLINE, Vol.6, 2009, issue
Jeong Hoon Doo, Man Yeong Ha, Hyun Sik Yoon
Natural Convection Enhancement on Micro-Grooved Surfaces
Journal of Enhanced Heat Transfer, Vol.1, 1994, issue 3
John C. P. Huang, Ting Wang, Scott P. Mislevy
A Numerical Study on Fluid Flow and Heat Transfer Performance of Internally Roughened Tubes with Dimples
Journal of Enhanced Heat Transfer, Vol.16, 2009, issue 3
R. Li, Yuan G. Lei, Y. B. Tao, Ya-Ling He, P. Chu
Heat Transfer Measurement of Confined Multiple Impinging Slot Jets without Cross-Flow Effects
International Heat Transfer Conference 12, Vol.13, 2002, issue
Bengt Sunden, Xiufang Gao
DRAG REDUCTION BY DIMPLES? − A COMPLEMENTARY EXPERIMENTAL/NUMERICAL INVESTIGATION −
TSFP DIGITAL LIBRARY ONLINE, Vol.5, 2007, issue
Michael Breuer, Hermann Lienhart, Cagatay Koksoy