ライブラリ登録: Guest
Begell Digital Portal Begellデジタルライブラリー 電子書籍 ジャーナル 参考文献と会報 リサーチ集
High Temperature Material Processes: An International Quarterly of High-Technology Plasma Processes
SJR: 0.137 SNIP: 0.341 CiteScore™: 0.43

ISSN 印刷: 1093-3611
ISSN オンライン: 1940-4360

High Temperature Material Processes: An International Quarterly of High-Technology Plasma Processes

DOI: 10.1615/HighTempMatProc.v4.i3.20
16 pages

OXIDATION OF STAINLESS STEEL PARTICLES WITH AND WITHOUT AN ALUMINA SHELL DURING THEIR FLIGHT IN A PLASMA JET

Helene Ageorges
University of Angers, LETP, 2 Boulevard Lavoisier, 49045 Angers Cedex, France
Pierre Fauchais
Laboratoire Sciences des Procedes Ceramiques et de Traitements de Surface UMR CNRS 6638 University of Limoges 123 avenue Albert Thomas, 87060 LIMOGES - France

要約

Investigations are carried out to study the oxidation of stainless steel particles collected after their flight in a plasma jet. In some tests, the injected particles are coated with an alumina shell. Particles are sprayed in Atmospheric Plasma Spraying (APS) and then collected in a concentric cylinder where they are quenched by argon jets. SEM observations of sprayed stainless steel particles show the formation of dark spots within their clear cross section, which displays the chromium and oxygen elements prominently. X-ray diffraction shows a chromium oxide phase which seems to be CrO. This is due to the convective movements within the particle renewing continuously fresh chromium at the surface and entraining the formed CrO inside the particle. It seems that, as for FeO, CrO is immiscible with liquid steel. On the other hand, alumina coated particles are less oxidized : cross sections present less oxide inclusions. Two types of particles were observed : some are still fully coated but the shell is broken due to the higher expansion of the stainless steel core. They probably result from particles where alumina has not been fully melted. Others have their alumina fused and entrained by liquid flow to the back of the moving droplet. Fused alumina droplets at the particles surface have coalesced creating a melted alumina cap. The two types of particles are probably due to the wide distribution trajectories within the spray cone which result in temperature differences. The particles with the alumina at the tail have probably traveled in the core of the plasma jet where temperatures are higher and then both materials have been melted, whereas the others have traveled in the jet fringes where the temperatures are lower.


Articles with similar content:

OXIDATION AND SPLATS OF STAINLESS STEEL PARTICLES COATED WITH AN ALUMINA SHELL
High Temperature Material Processes: An International Quarterly of High-Technology Plasma Processes, Vol.14, 2010, issue 4
Helene Ageorges, Pierre Fauchais
OXIDATION AND SPLATS OF STAINLESS STEEL PARTICLES COATED WITH AN ALUMINA SHELL
Progress in Plasma Processing of Materials, 2001, Vol.0, 2001, issue
Helene Ageorges, Pierre Fauchais
PLASMA SPRAYED COATINGS OF MECHANOFUSED ALUMINA-STEEL PARTICLES
High Temperature Material Processes: An International Quarterly of High-Technology Plasma Processes, Vol.14, 2010, issue 4
Helene Ageorges, Alain Grimaud, Pierre Fauchais
COALESCENCE AND AGGLOMERATION OF DROPLETS SPRAYED ON A SUBSTRATE
Atomization and Sprays, Vol.27, 2017, issue 1
Sanjeev Chandra, Alireza Dalili, Javad Mostaghimi, Javad Esmaeelpanah
HEAT TRANSFER ANALYSIS DURING JET IMPINGEMENT ON METAL PLATES
International Heat Transfer Conference 16, Vol.7, 2018, issue
Eckehard Specht, Yuan Fang